Advice

Brick vs Cladding in Australia

Last updated: October 2026

The exterior wall system is one of the largest visual and performance decisions in a new build. The headline framing is brick versus cladding, but the practical decision is more layered than that: brick itself splits into double brick and brick veneer (which sits structurally inside the cladding category), and cladding is a broad family covering weatherboard, fibre cement, metal, timber, render and stone. This guide is the practical decision framework: what each system actually is, how each performs across Australia's regional contexts, and how to settle the choice with your builder, designer and engineer.

The short answer: when each system fits

Brick (typically brick veneer in most eastern states, double brick in WA and parts of SA) typically fits traditional aesthetic preferences, hot dry inland climates that benefit from thermal mass, established suburbs where brick is the visual norm, heritage and character overlay zones, long-term ownership horizons that value minimal maintenance, and properties where acoustic performance against external noise matters.

Cladding (fibre cement, weatherboard, metal, timber, render or stone) typically fits modern architectural intent, cyclone and BAL-29 plus bushfire-prone regions where lightweight non-combustible systems are advantageous, sloped or complex sites where brick weight is a structural challenge, faster build programmes, and renovation or extension work where matching existing brick is impractical or undesirable.

Brick veneer (the middle category) is the Australian residential default - timber or steel frame as the structural element with a single brick exterior leaf - and combines brick aesthetic with frame-build economics. For most standard residential projects, brick veneer is a credible default; the question is whether the climate, design intent or ownership preference points elsewhere.

What "brick construction" actually means in Australia

Double brick (full brick / cavity brick)

Double brick uses two leaves of brick separated by an air cavity, with the inner leaf often load-bearing for the structure above. Historically dominant across most of Western Australia and common in parts of South Australia, double brick has slowly retreated in market share elsewhere as brick veneer and cladding have grown. The system carries excellent thermal mass and acoustic performance, but is heavy enough to require engineered foundations and footings from the outset.

The build programme is materially slower than brick veneer because the inner leaf goes up before the floor and roof structure on top. Cost varies meaningfully by region but typically adds approximately $20,000 to $60,000 plus to a residential build compared with brick veneer.

Brick veneer

Brick veneer uses a single leaf of brick attached to a timber or steel frame. The frame is the structural element; the brick provides the exterior weather-protection layer along with thermal mass and the visual brick character. Brick veneer is the dominant Australian residential exterior wall method in most eastern states, accounting for approximately 60 to 70 per cent of new home builds.

Structural loading is significantly lower than double brick, and the build programme is faster because the frame and brick can be sequenced more flexibly. Underneath the brick, the frame choice (timber or steel) determines a range of secondary characteristics - termite handling, thermal bridging, acoustic transmission. See our guide on timber frame vs steel frame in Australia for the frame decision that sits beneath any brick veneer wall.

Why the distinction matters

"Brick" in real estate listings across most eastern states typically means brick veneer; double brick is usually advertised explicitly because the assembly carries a perception premium. Performance characteristics differ between the two - double brick delivers more thermal mass and acoustic dampening, brick veneer delivers a faster build programme and meaningfully lower cost. The headline visual is similar; the assembly behind it is not.

What "cladding" covers - the main exterior wall systems

Cladding is a family of exterior wall systems rather than a single material. The categories below cover the mainstream Australian residential options.

Weatherboard (timber and composite)

Weatherboard covers traditional timber boards (hardwood, treated pine, cedar, Western Red Cedar) and modern composite alternatives (engineered timber and fibre cement weatherboard profiles). The aesthetic association is Federation, country, coastal modernism and Queenslander styles, and the category remains visually defining in many established suburbs.

Fibre cement (sheet and plank)

Fibre cement is a major Australian product category supplied by James Hardie, Scyon and similar manufacturers. Sheet form delivers large flat panels suited to express modernism; plank form delivers weatherboard-style profiles at lower cost than timber. The category is fire-resistant, termite-resistant, dimensionally stable and one of the more versatile cladding choices for Australian residential builds.

Metal cladding

Metal cladding typically uses Colorbond steel profiles applied vertically. Standing seam metal cladding sits at the architectural premium end. Aluminium composite panel (ACP) is now uncommon in Australian residential construction following past combustibility issues and has largely retreated to specific commercial applications. Metal cladding reads as modern architectural intent and is widely used in coastal modernism.

Timber and timber composite

Solid timber cladding (spotted gum, blackbutt, cypress) and design-led treatments such as charred timber (shou sugi ban) deliver distinct aesthetic outcomes. Composite timber products (such as ModWood) offer improved durability and reduced maintenance compared with raw timber. The category carries higher maintenance demands than other cladding types and is most often chosen for design intent rather than performance economy.

Lightweight render systems

Lightweight render covers acrylic render over fibre cement substrate, autoclaved aerated concrete (AAC) blocks rendered to finish, and foam-based panel systems with render finish. The aesthetic is contemporary and the category is widely used in apartment and townhouse construction as well as detached homes seeking a modern minimalist exterior. See our dedicated guide on render vs cladding in Australia for a closer look at this specific comparison.

Stone cladding

Stone cladding covers natural stone veneer and reconstituted stone products. The category is premium in both aesthetic and cost, and is most often used as a feature element on a portion of the exterior rather than the whole envelope. See our guide on stone cladding in Australia for the detailed type, cost and specification picture.

A note on brick veneer

Brick veneer is technically and structurally a cladding system - a single non-load-bearing brick leaf attached to a frame. It sits in the brick category in this guide because the visual outcome and homeowner intent are brick-led, but the assembly logic belongs to the cladding family.

Side-by-side comparison: cost, durability and performance

The table below summarises the practical comparison points homeowners ask about most. Cladding is treated as the main non-brick categories collectively, with specific differences noted in the sections that follow.

TopicBrick (veneer)Cladding
Material + labour costBrick veneer typically lowerMid for fibre cement / weatherboard, premium for stone
Installation tradeBricklayer (variable regional availability)Carpenter or specialist installer
Lifespan100+ years with maintenance30 to 100+ years depending on type
Maintenance intervalRe-point every 30 to 50 yearsPaint or refresh every 5 to 15 years (timber/fibre cement)
Thermal massHigh (especially double brick)Low - performance driven by insulation
Acoustic performanceExcellentLower without assembly upgrades
Termite vulnerabilityNoneTimber vulnerable, fibre cement and metal none
Fire performanceNon-combustibleNon-combustible (fibre cement, metal); timber requires treatment
Build programmeLonger (bricklayer scheduling)Faster (parallel trade work)
Aesthetic flexibilityBrick palette onlyWide range of materials, profiles and colours

The table highlights what is and what is not actually different. Lifespan and weather performance are broadly equivalent across mainstream specifications when correctly installed. The genuine differences cluster around thermal mass, acoustic performance, maintenance intervals, build programme and aesthetic flexibility.

Climate suitability across Australia

Climate zone and local hazard exposure are among the strongest signals in the brick-vs-cladding decision. The patterns below summarise typical performance across major Australian regional contexts.

Tropical north (Cairns, Darwin, Top End)

Cyclone exposure in Category C and D regions favours lightweight cladding systems for ease of engineered tie-down. Brick veneer can perform with engineered cyclone-rated fixings but is less commonly the practical default. High humidity and termite pressure favour non-timber cladding (fibre cement, metal) or carefully treated timber alternatives.

Coastal subtropical (South-East Queensland, Northern NSW)

Both perform well. Brick remains dominant in established suburbs, with cladding increasingly chosen in new builds and contemporary renovations. Fibre cement is well-suited to high humidity; timber cladding requires more attention to maintenance.

Temperate (Sydney, Melbourne, Adelaide, Hobart)

Brick veneer historically dominates in many established suburbs, with cladding gaining share in contemporary builds and renovations. Thermal mass of brick is valued through hot summers and cold winters, but a well-insulated cladding wall can match the practical comfort outcome.

Hot dry inland (regional NSW, SA, WA)

Brick excels through its thermal mass advantage in climates with strong diurnal temperature swings. Double brick is particularly common in inland Western Australia for the same reason. Cladding is workable with strong insulation specification but does not match the passive thermal performance of mass brick walls in this band.

Bushfire-prone areas (BAL-29 and above)

Non-combustible exteriors (brick, fibre cement, metal) are typically preferred. Timber cladding requires fire-treated specification and detailed assembly to comply at higher BAL ratings. See our guide on BAL ratings in Australia for the underlying classification framework, and our cluster guide on roof tiles vs metal roofing in Australia for the coordinated roofing decision in BAL-rated areas.

Coastal salt zones (within roughly 1km of coast)

Brick performs well with appropriate mortar selection. Metal cladding requires marine-grade specification (such as ZAM coating). Fibre cement performs well in coastal exposure with standard installation. See our guide on the coastal home in Australia for the broader coastal material specification picture, and the best insulation for Australian climate by region for envelope thermal detail.

Bushfire, cyclone and storm performance

Bushfire

Brick is non-combustible and delivers excellent ember and radiant heat performance. Fibre cement and metal cladding are also non-combustible and perform strongly. Stone cladding is non-combustible. Timber cladding is combustible unless fire-treated and detailed for BAL compliance per AS 3959. Across BAL ratings, brick or non-combustible cladding deliver the most direct compliance pathway. See our guide on BAL ratings in Australia for the rating-specific detail.

Cyclone (Category C and D regions)

Brick veneer requires engineered cyclone tie-down systems in Category C and D regions; the heavy weight is both an advantage (wind resistance) and a constraint (loaded fixings, foundation engineering). Cladding systems are lightweight and can be engineered to AS 1170 wind loadings with greater flexibility. Both can comply; the engineering specification is the determinant rather than the material category itself.

Storm and hail

Brick is highly hail-resistant and the most robust mainstream exterior under hail impact. Fibre cement is dent-resistant. Metal cladding dents under hail but typically maintains its weather seal - the damage is primarily cosmetic. Timber cladding is the most vulnerable to hail damage and dents or cracks more readily under impact.

Thermal performance and energy efficiency

Thermal mass

Brick - and especially double brick - carries significant thermal mass that delays heat transfer through the wall. This is most beneficial in climates with strong diurnal temperature variation (hot dry inland, parts of WA and SA). Cladding systems carry minimal thermal mass; their thermal performance depends almost entirely on insulation specification.

Insulation specification

Both systems require insulation behind the exterior, and wall thermal performance is driven primarily by the insulation R-value rather than the exterior material on its own. Brick veneer wall assemblies typically achieve R2.0 to R2.5 with standard batt insulation in the frame cavity. Cladding wall assemblies typically achieve R2.5 to R3.0 with batt plus reflective foil, and can reach R4.0 plus with rigid insulation board added.

What actually drives wall thermal performance

The dominant drivers are wall insulation R-value, thermal bridging (a meaningful concern with steel frame in brick veneer assemblies), air sealing and weatherproofing detailing, and window-to-wall ratio with glazing specification. Wall material itself contributes meaningfully but rarely changes the NatHERS outcome on its own. See our guides on insulation in Australia, NatHERS ratings in Australia and the best insulation for Australian climate by region for the detailed picture.

Maintenance over the lifespan

Brick

Routine brick maintenance is minimal. Re-pointing - refreshing the mortar joints - is typically required every 30 to 50 years at an indicative cost of $5,000 to $15,000 on a typical residential home, varying by home size and access. Pressure washing every 10 to 20 years restores the surface appearance. Individual brick replacement is possible but matching aged brick reliably is difficult; the practical reality is that small replacement zones are visible against weathered original brick.

Fibre cement

Fibre cement requires a paint refresh every 10 to 15 years at an indicative cost of $5,000 to $15,000 depending on home size. Localised damage repair is straightforward - sheet or plank replacement and repaint. Failure modes are paint deterioration and occasional edge damage rather than substrate failure.

Weatherboard timber

Timber weatherboard requires a paint or oil refresh every 5 to 10 years (oils more frequently than paint) at an indicative cost of $5,000 to $15,000. The most common long-term failure mode is wood rot in exposed areas where maintenance has lapsed. Cedar shingles and similar premium products carry longer intervals between attention but higher replacement costs when needed.

Metal cladding

Metal cladding requires minimal regular maintenance. Paint refresh is typically required at end of paint life - 30 to 40 years for standard Colorbond, longer for premium specifications. Failure modes cluster around fastener deterioration and edge corrosion, particularly in coastal zones without the correct marine-grade specification.

Stone cladding

Stone cladding requires minimal regular maintenance. Re-pointing is required if the application is mortared. Cleaning every 10 to 20 years restores surface appearance. The category sits closest to brick on long-term maintenance economics.

Insurance implications

Building insurance premiums are typically similar across exterior systems in non-cyclone, non-bushfire regions. In bushfire-prone areas, non-combustible exteriors (brick, metal, fibre cement) sometimes attract a modest premium reduction relative to timber cladding. In cyclone regions, engineered brick and compliant cladding systems are typically equally acceptable to insurers; the engineering specification matters more than the material category.

In hail-prone regions across the eastern seaboard, brick and metal often see preferential treatment in some underwriting, reflecting lower cosmetic claim frequency. Timber cladding can attract occasional underwriting questions about fire protection and maintenance regime. Insurance considerations rarely drive material choice on their own but are worth verifying at design stage if the budget is tight. See our guide on construction insurance in Australia for the broader picture during the build itself.

Resale and aesthetic considerations

Aesthetic intent

Brick reads as traditional Australian residential character and is the expected exterior in many established suburbs. Modern brick treatments - sleek bricks, textured bricks, dark bricks - now carry contemporary architectural intent and are increasingly chosen in new builds for design reasons rather than tradition. Fibre cement is versatile and reads as contemporary residential. Weatherboard timber sits with Federation, country, coastal and Queenslander styles. Metal cladding is a defining cue of modern architecture and coastal modernism. Stone cladding signals premium aesthetic and is most often used as a feature element. Mixed-material exteriors are increasingly common, with brick or stone bases combined with cladding to upper floors.

Resale

The Australian residential market accepts all major exterior systems at resale and the material itself rarely drives the sale decision. Established suburbs often expect brick; new estates and contemporary suburbs increasingly accept and prefer mixed-material and cladding-forward designs. Buyer perception varies regionally; condition, finish quality and design integration typically dominate over the material category.

Heritage and character overlay considerations

Some local councils specify brick, weatherboard or specific exterior treatments in heritage or character overlay zones. Verify council requirements before specifying material if the property sits in a controlled area; the cost of being asked to change material during approval is significant. See our guide on heritage homes in Australia for the broader heritage overlay framework.

The cost overview (with link to deep-dive)

Cost is rarely the deciding factor at the residential scale; climate, aesthetic, maintenance preference and build programme typically matter more. As an indicative overview of installed cost per square metre of wall area:

  • Brick veneer: typically $90 to $150 per square metre
  • Fibre cement (plank or sheet): typically $80 to $140 per square metre
  • Weatherboard timber: typically $100 to $180 per square metre
  • Metal cladding (Colorbond): typically $90 to $150 per square metre
  • Stone cladding: typically $200 to $400 plus per square metre
  • Standing seam architectural metal: $250 to $500 plus per square metre

On a typical 200 square metre home with approximately 250 square metres of wall area, brick veneer typically lands in the $22,500 to $37,500 range. Double brick adds approximately $20,000 to $60,000 plus over brick veneer. Cladding cost varies widely by category, from broadly comparable to brick veneer (fibre cement) up to materially more expensive (stone, premium metal). For the comprehensive cost picture across the whole build, see our guide on the cost to build a house in Australia.

Project types that suit brick

Brick is typically the right fit for: standard residential builds in temperate climates with traditional aesthetic intent; established suburbs where brick is the visual character norm; hot dry climates that benefit from thermal mass; long-term ownership horizons that prioritise minimal maintenance; heritage overlay zones requiring brick specification; Western Australian and inland South Australian climates particularly suited to double brick; owner-builders comfortable with bricklayer subcontracting timelines; and properties where acoustic performance against external noise (busy roads, near commercial zones, near transport corridors) materially affects daily comfort.

Project types that suit cladding

Cladding is typically the right fit for: modern architectural intent and contemporary design; cyclone-prone regions where lightweight engineered systems are favoured; BAL-29 and above bushfire areas where non-combustible non-brick options carry a simpler compliance pathway; sloped or complex sites where brick weight is a structural challenge; renovation and extension work where matching existing brick is impractical or undesirable; faster build programmes where bricklayer scheduling is a binding constraint; coastal modernism aesthetic where weatherboard, fibre cement plank or metal cladding define the look; mixed-material designs where cladding to upper floors over a brick base delivers the visual outcome; and owner-builders without easy access to bricklaying trades in their region.

How to make the final decision for your exterior

Six questions, in order, settle most brick-vs-cladding decisions for residential homeowners.

  1. What is the property's climate zone and hazard exposure - cyclone, bushfire (BAL rating), coastal salt, hot dry inland?
  2. What is the design intent and aesthetic preference - traditional brick, contemporary cladding, mixed-material?
  3. What is the suburb's established character - is there a heritage or character overlay that may specify the material?
  4. What is the long-term maintenance tolerance - minimal attention, or comfortable with paint cycles every 5 to 15 years?
  5. What is the budget tolerance for the material premium - particularly for double brick or stone cladding?
  6. What is the build programme priority - is faster delivery via cladding worth more than the assembly characteristics of brick?

When to involve the architect or building designer

Heritage overlay compliance, architectural intent, integration with the broader design and any mixed-material strategy all benefit from the design professional's involvement before the exterior material is locked in. See our guide on building designer vs architect in Australia for the choice between the two professions.

When to involve the structural engineer

Engage a structural engineer for double brick load-bearing design, cyclone-region engineering for either system, complex sites with structural implications, and any project where the exterior wall choice affects foundation or footing design. See our guide on structural engineers in Australia.

When to involve the builder early

Local trade availability, cost validation in your specific market and build programme implications all warrant the builder's input early. Bricklayer availability in particular varies meaningfully by region and can be a binding programme constraint at peak periods. See our guide on how to vet a builder in Australia for the broader builder selection framework.

BUILTLY and lasting project records

BUILTLY is building a record of completed Australian homes that credits the builder, architects, designers and trades behind each one.

BUILTLY is building a record of completed Australian homes that credits the builder, designers and trades behind each one.

BUILTLY is building a record of completed Australian homes that credits the builder, designers and trades behind each one.

Frequently Asked Questions

Is double brick worth the extra cost over brick veneer in Australia?

It depends on the climate and the ownership horizon. Double brick adds approximately $20,000 to $60,000 plus to a typical residential build over brick veneer, varying by home size and region. The genuine performance gains are thermal mass (more useful in hot dry inland climates with strong diurnal swings), acoustic performance (notable on busy roads or near commercial zones) and longevity at the structural level. In temperate climates and standard suburban contexts, the practical gain over a well-insulated brick veneer wall is modest and the cost is rarely repaid through energy savings alone. Double brick is most often justified by climate fit (Western Australia, hot dry regions), site conditions, or owner preference for the assembly itself rather than spreadsheet payback.

Can I mix brick and cladding on the same home?

Yes, and mixed-material exteriors are increasingly common in Australian residential design. Typical patterns include a brick base or ground floor with weatherboard, fibre cement or metal cladding to the upper floor; brick to the front facade with cladding to side and rear elevations; or a feature stone or timber cladding panel set within a predominantly brick exterior. Mixed materials add visual interest, can reduce overall material cost, and allow lighter cladding on harder-to-access elevations. The key coordination points are weatherproofing detailing where the materials meet, consistent thermal performance across the assemblies, and aesthetic balance. Engage the architect or building designer early so the material transitions are designed rather than improvised on site.

Which is faster to build with - brick or cladding?

Cladding is typically faster. Cladding installation is carpenter-led work that can run in parallel with other trades and is less weather-dependent than bricklaying. Brick veneer adds a discrete bricklayer phase to the programme and is more sensitive to bricklayer subcontractor availability, which can be a binding constraint in regional markets and during peak periods. Double brick adds further programme time because the inner leaf goes up before the floor and roof structure on top. As an indicative range on a typical single-storey home, cladding can save several weeks compared with brick veneer, and substantially more compared with double brick. Programme is rarely the deciding factor on its own, but it can matter on tight settlement timelines or rental-bridging budgets.

Does cladding affect resale value compared to brick in Australia?

Generally no, when comparing well-executed examples of each. The Australian residential market accepts brick, fibre cement, weatherboard, metal and stone cladding at resale, and condition, finish quality and overall design integration typically dominate over the material itself. Regional patterns matter: established inner-suburban markets often expect brick and a non-brick exterior can read as out of character; new estates and contemporary suburbs accept and often prefer mixed-material and cladding-forward designs. Heritage and character overlay zones may specify brick or a particular cladding type by council requirement. The honest summary is that the material is a secondary factor at resale; what moves price is whether the exterior reads as well-designed and well-maintained for the suburb it sits in.

Is fibre cement cladding really as durable as brick?

Not quite, but the gap is narrower than the popular perception suggests. Modern fibre cement cladding products (Scyon, James Hardie and similar) typically deliver 50 plus year service life with a paint refresh every 10 to 15 years. Brick exterior typically delivers 100 plus years with minimal maintenance and re-pointing every 30 to 50 years. The brick longevity advantage is real but expressed over a much longer ownership horizon than most homeowners hold a single property. Fibre cement is non-combustible, dimensionally stable, termite-resistant and well-suited to Australian climates. For most owners and at most ownership horizons, the practical durability difference is paint cycles rather than wall replacement. Brick remains the longest-lived option; fibre cement is durable enough for nearly all residential contexts.