A rainwater tank is one of the few items in an Australian house that is simultaneously a regulatory requirement, a piece of household infrastructure and a long-term running cost saving. It is also one of the most commonly rushed decisions on a build, chosen late from a supplier catalogue rather than designed alongside the roof and the drainage.
Why rainwater tanks matter
Australia has the most variable rainfall of any inhabited continent, and residential water policy across the states has responded by pushing capture and reuse onto individual properties. For a new build, that shows up in two ways: a compliance obligation in several jurisdictions, and a practical opportunity to take a meaningful share of household water demand off the mains supply.
The everyday uses are well established. Garden and lawn irrigation is the simplest, because it needs no internal plumbing. Toilet flushing and the laundry cold tap are the two internal connections that regulators most often nominate, because they are high volume, non-potable and easy to isolate from the drinking supply. In areas without reticulated mains water, the tank is the drinking supply, which raises the standard of the catchment, the screening and the treatment considerably.
This guide covers capture and storage on the property: whether you need a tank, what type and size to install, how it is plumbed, what it costs, and how it is maintained. It is deliberately separate from how water leaves the site. For pit and pipe design, surface falls, detention and the overall site drainage strategy, see the BUILTLY guide to stormwater drainage design in Australia. For the council-approved point at which your stormwater is allowed to connect to the public system, which is where tank overflow ultimately ends up, see stormwater legal point of discharge in Australia.
For the surrounding build context, including specifications, variations and the handover record, refer to the BUILTLY complete guide to building a house in Australia.
When rainwater tanks are required
There is no national rule requiring a rainwater tank on a new dwelling. The obligation comes from state sustainability schemes, state plumbing provisions and council planning conditions, and the three can apply at once. The practical consequence is that the same house design can require a tank in one state, satisfy the rules another way in the next, and attract no requirement at all somewhere else.
State-level schemes
In New South Wales, new dwellings are assessed against a water reduction target under the BASIX scheme. A tank plumbed to toilets, the laundry cold tap and outdoor taps is the most common way to reach the target, though it is a target rather than a prescribed product, and other measures contribute. The certificate commitments become conditions of approval, so what is entered at design stage must be what is installed.
In South Australia, new dwellings must provide an additional water supply connected to nominated fixtures, which in the great majority of cases is delivered as a rainwater tank plumbed internally. In Victoria, water and energy provisions for new homes are typically satisfied through a package of measures in which a tank plumbed to toilet flushing is one of the standard options. In Queensland, Western Australia, Tasmania, the ACT and the Northern Territory, the requirement is more often driven by the council, by water sensitive urban design policy, or by the absence of a reticulated supply.
Council and site-specific conditions
Independently of any state scheme, a council can condition an approval to require rainwater capture. This is most common where the receiving stormwater network is capacity-constrained, where impervious site coverage is high, or where local policy sets a water sensitive urban design standard. In those cases the tank may be required to serve two purposes at once, holding a detention volume as well as a supply volume, which changes both the sizing and the outlet arrangement.
BUILTLY is building a record of completed Australian homes that credits the builder, designers and trades behind each one.
Requirements are stated as a package: a minimum tank volume, a minimum connected roof catchment area, and a list of fixtures the tank must serve. Meeting the volume while connecting only half the nominated catchment is a common and expensive compliance failure at final inspection.
Tank types and sizing
Above-ground, slimline and underground
Round above-ground tanks give the lowest cost per litre and the simplest installation, but they need genuine yard space and they are visible. Slimline tanks trade cost per litre for footprint, sitting against a wall or in a side setback where a round tank would not fit, which is why they dominate on smaller urban lots. Underground and under-deck tanks free the yard entirely and are the usual answer on tight sites, at a substantially higher installed cost because of excavation, structural requirements and the need for a pump to lift water back out.
Material options
- Polyethylene - the default for residential above-ground tanks. Light, corrosion-proof, wide range of shapes and colours, straightforward to install. Quality varies, so check the material is rated for potable water and carries UV stabilisation
- Steel with a food-grade liner - a slim profile and a long life where the liner is intact, and often chosen for appearance. The liner is the vulnerable component and the wall benefits from being protected from impact
- Concrete - the standard for in-ground installations and large capacities. Heavy, durable, keeps water cool and dark, and can be trafficable if designed for it. Highest cost and requires crane or in-situ construction
- Bladder tanks - installed in the cavity under a suspended floor or deck. Useful where nothing else fits, limited in capacity and sensitive to the condition of the space they sit in
Sizing from roof catchment
Yield is a function of connected catchment area, not total roof area. Only the roof planes whose downpipes actually run to the tank count. The working figure is that one millimetre of rain falling on one square metre of connected roof produces close to one litre, before allowing for losses to wetting, evaporation and the first-flush diversion.
On a 150 square metre connected catchment, a 20 millimetre rain event yields roughly 3,000 litres less losses. That single figure tells you two useful things: a very small tank on a large catchment will spend most of its life overflowing, and a very large tank in a low-rainfall or seasonal-rainfall area will rarely fill.
Sizing against intended use
- Garden and outdoor taps only - 2,000 to 5,000 litres suits most suburban blocks, with demand concentrated in exactly the drier months when the tank is lowest
- Toilet and laundry connection - 3,000 to 10,000 litres is the common band for a family home, because the demand is steady year-round and worth buffering
- Whole-of-house supply with no mains - typically 20,000 litres and upwards, sized from household demand across the longest dry period on record rather than from average rainfall
- Compliance-driven installations - the scheme or condition sets the minimum volume and the minimum connected catchment, so treat that as the floor and size upward if the intended use justifies it
Plumbing and connection requirements
Everything downstream of the downpipe is licensed plumbing work. The installation is inspected, it forms part of the plumbing compliance record for the property, and shortcuts here are what turn a tank into a defect rather than an asset.
Inlet, screening and first flush
Every inlet, overflow and vent opening needs insect-proof mesh screening, primarily to keep mosquitoes out of a standing water body. Leaf guards or gutter mesh reduce the organic load reaching the tank and lengthen the interval between cleanouts.
A first-flush diverter discards the opening volume of each rain event, which carries the accumulated dust, leaf litter and droppings from the roof. The chamber fills, seals, and then lets cleaner water through, draining down slowly so it is armed again for the next event. It is a modest cost and it does more for stored water quality than any other single component.
Mains backup and switching
Where a tank supplies internal fixtures, the household cannot be left without water when the tank runs dry, so a dual-supply arrangement is used. An automatic switching device changes the supply to those fixtures over to mains water when the tank level drops, and returns to tank water when it recovers. Some arrangements top the tank up with mains instead, which is generally less desirable because it can dilute the conservation benefit and needs careful protection at the inlet.
Backflow prevention is the non-negotiable part. Any point where mains water can meet tank water requires protection so that non-potable water cannot travel back into the drinking supply, whether that is an air gap at a top-up inlet or an approved backflow prevention device on the mains connection. Water authorities take this seriously and it is checked.
Pumps and pipework identification
Gravity feed is adequate for a garden tap on a raised tank, but internal fixtures need a pump. Pressure pumps are commonly the noisiest item added to a house, so position the pump away from bedroom windows and away from the neighbouring boundary, and use an enclosure if the location is tight. Non-potable pipework and outlets must be identified and labelled so a future occupant or tradesperson does not mistake tank supply for drinking water.
Overflow into site drainage
A full tank passes almost its entire inflow out of the overflow, so the overflow must be piped into the approved site drainage at a capacity at least matching the inlet. Terminating it at ground level beside the tank saturates the soil against footings and pushes water onto neighbouring land. Where the tank also carries a detention function imposed by council, the outlet is restricted deliberately and the sizing is an engineering calculation rather than a supplier default. How that overflow reaches the street or the approved connection is covered in the stormwater guides linked above.
Cost considerations
Tank supply is usually the smaller half of the number. Base preparation, plumbing, the pump and the switching device frequently cost as much as the vessel itself, and underground installation changes the order of magnitude.
- Poly tank supply - broadly $600 to $1,500 for 2,000 to 5,000 litres, and roughly $1,200 to $3,000 for 5,000 to 10,000 litres, with slimline shapes carrying a premium per litre
- Steel tank supply - generally a step above equivalent poly capacity, chosen for profile and appearance
- Concrete and underground tanks - commonly $6,000 to $15,000 and beyond once excavation, delivery, backfill and structural requirements are included
- Base preparation - a compacted crushed rock pad or a concrete slab, typically several hundred to a couple of thousand dollars depending on size and access
- Plumbing and pump - downpipe diversion, first-flush device, pump, switching device and internal connection to toilets and laundry commonly runs $1,500 to $4,000
- Detention conversion - where council conditions a detention volume, expect additional engineering, a controlled outlet and compliance certification
Ranges are indicative for 2026 planning and vary with site access, crane requirements, run lengths and region. Quote the installed system, not the tank.
Rebates
The broad state-level rainwater tank rebate programs that ran through the drought years have largely been discontinued, and no reliable nationwide incentive currently exists for a standard residential installation. What remains is patchy and local: some councils and some regional water authorities offer modest rebates or discounted tanks, occasionally tied to connecting the tank to internal fixtures. Because these open, close and change value without much notice, no figure should be assumed. Check your council and your water authority directly at the time you commit, and treat any rebate as a bonus rather than part of the business case.
Maintenance and water quality
A tank is a low-maintenance item, not a no-maintenance one, and almost all of the work is at the inlet rather than in the tank.
Routine maintenance
- Clear gutters and leaf guards regularly, and more often under deciduous trees or in a bushfire-prone area
- Check the first-flush chamber drains down fully between events, since a blocked chamber stops diverting
- Inspect inlet, overflow and vent screens for tears, which is how mosquitoes and vermin get in
- Keep overhanging branches trimmed back from the connected catchment
- Check the pump and switching device operate as intended, particularly after a long dry spell
- Inspect for accumulated sludge every two to three years and desludge when the base layer becomes significant
Water quality and potable use
For garden, toilet and laundry use, good screening, a working first-flush diverter and clean gutters are generally sufficient. Where the tank supplies drinking water, the standard rises. The catchment must be suitable, meaning no lead flashing, no unsuitable roof coatings, and no discharge from flues or evaporative units onto the collecting planes. Filtration and disinfection should be considered, and periodic testing is the only way to confirm what is actually in the water rather than what is assumed.
Situations that warrant extra care
Properties near heavy industry, busy arterial roads, agricultural spraying or recent bushfire activity carry a higher contamination risk on the roof surface. In those settings, treat potable use as a decision requiring testing rather than a default, and consider isolating the tank from the catchment after a significant smoke or dust event until the roof has been washed by rain.
What to check before installation
- Confirm whether a tank is a condition of your approval, and if so the exact minimum volume, minimum connected catchment and nominated fixtures
- Confirm which roof planes and downpipes are actually being connected, marked on the plan rather than agreed verbally
- Confirm the tank location against setbacks, easements, access for delivery or crane, and clearance from the boundary
- Confirm the base type and who is responsible for preparing it, since this is a frequent gap between builder and tank supplier scopes
- Confirm the overflow route and its connection into the approved site drainage, at a capacity matching the inlet
- Confirm a first-flush diverter and insect-proof screening are included rather than optional extras
- Confirm the mains switching arrangement and the backflow protection method for internal connections
- Confirm pump location, noise mitigation and the electrical supply to it
- Confirm non-potable outlets will be labelled and the pipework identified
- Obtain the plumbing compliance certificate, product warranties and the pump manual as part of your handover pack
All of this is licensed work, so it is worth confirming who is performing it and under what licence before the work starts. The BUILTLY guide on how to check a builder's licence in Australia covers the verification process and the state registers.
BUILTLY and lasting project records
A tank installation is easy to see and hard to verify. The connected catchment, the first-flush device, the switching arrangement, the backflow protection and the overflow route all sit behind or below the visible vessel, and they are the parts that determine whether the system performs and complies. Recording the installed specification and the plumbing certification at completion turns an assumption into checkable evidence for the next owner, the next trade and any future valuation.
BUILTLY is building a record of completed Australian homes that credits the builder, designers and trades behind each one.
Frequently asked questions
Is a rainwater tank compulsory for a new home in Australia?
It depends on the state and the council. There is no single national rule. In New South Wales, the BASIX water target applies to new dwellings and is very commonly met by installing a tank plumbed to toilets, the laundry cold tap and outdoor taps, although other measures can contribute. In South Australia, new dwellings are required to provide an additional water supply plumbed to specified fixtures, which in practice is usually a rainwater tank. In Victoria, energy and water provisions for new homes are typically satisfied through a package that can include a tank plumbed to toilets. Queensland, Western Australia, Tasmania, the ACT and the Northern Territory rely more heavily on council-level and site-specific conditions. Confirm the requirement with your certifier and council before the design is locked in.
What size rainwater tank do I need?
Sizing is driven by three things: connected roof catchment area, local rainfall pattern, and what the water will be used for. A useful planning rule is that one millimetre of rain on one square metre of connected roof yields close to one litre, less a small allowance for losses and first flush. Where a tank is being installed to satisfy a regulatory requirement, a minimum volume and a minimum connected catchment area are usually both specified, so the compliance figure sets the floor. For garden-only use, 2,000 to 5,000 litres is common. For toilet and laundry connection in a family home, 3,000 to 10,000 litres is a typical range, with larger volumes justified where rainfall is seasonal.
What is a first-flush diverter and do I need one?
A first-flush diverter discards the initial volume of runoff from a rain event, which carries the dust, leaf litter, bird droppings and roof debris accumulated since the last rain. That first wash is where most of the contamination sits. The diverter fills a small chamber, then seals and allows subsequent cleaner water to pass into the tank, draining slowly afterwards so it is ready for the next event. It is strongly recommended on any tank and is generally treated as necessary where the water will be used inside the dwelling.
Can I drink rainwater from a tank?
In much of rural Australia, tank water is the primary drinking supply and has been for generations. In urban areas where reticulated mains water is available, health authorities generally advise using mains water for drinking and cooking, and reserving tank water for garden, toilet and laundry use. If you intend to drink tank water where mains is available, the catchment needs to be suitable, the tank needs proper insect-proof screening and a first-flush diverter, the roof should be free of lead flashing and unsuitable coatings, and treatment such as filtration and disinfection should be considered. Testing is the only way to know what you actually have.
Where does the tank overflow go?
Overflow is a stormwater connection, not an afterthought. A full tank in sustained rain passes essentially its whole inflow straight out of the overflow, so the overflow has to be piped to the approved discharge arrangement for the property at a capacity at least equal to the inlet. Discharging it onto the ground next to the tank is a common cause of saturated soil against footings and boundary disputes with neighbours. The overflow route should appear on the hydraulic or drainage plan approved for the build.