Advice

Soil Classification Australia: What Your Soil Report Means

Last updated: October 2026

Your soil test has come back and it says Class H2. Or Class P. Or Class E. If you do not know what these classifications mean, you are not alone, most Australian homeowners who commission a soil test receive a report they cannot interpret. Soil classification in Australia is defined under Australian Standard AS 2870, Residential Slabs and Footings, and it determines how your home's footing system must be designed, what it will cost and how much risk the site carries. Understanding your soil classification before design commences is one of the most practically important steps in any residential construction project. This guide explains every classification, what each one means for your build and what to do with the information.

What is soil classification and why does it matter?

Soil classification in Australia is a system defined under Australian Standard AS 2870 that categorises residential building sites according to the reactivity of the soil, its tendency to expand and contract with changes in moisture content. The classification determines the minimum footing system design requirements for a residential building on that site.

Reactive soils, clays that expand when wet and contract when dry, are the primary subject of the classification system. The movement created by reactive clay soils can crack footings, slabs and walls if the foundation system is not designed to accommodate the specific reactivity of the site. The more reactive the soil, the more robust, and more expensive, the footing system required.

Soil classification matters for four practical reasons:

Footing design. The structural engineer uses the soil classification to design the footing system, slab thickness, beam depth, reinforcement and any additional engineering measures required. A footing system designed for the wrong soil class is either over-engineered and wasteful or under-engineered and at risk of failure.

Construction cost. Higher soil classifications require more substantial footing systems, more concrete, more reinforcement, deeper beams. The cost difference between a Class M footing and a Class H2 or Class E footing on the same house can be $10,000 to $50,000 or more depending on the house size and the specific engineering response required.

Insurance and warranty. Structural defects caused by inadequate footing design for the site's soil classification are not covered by home warranty insurance if the builder was aware of the classification and used an inadequate footing system. The soil classification is the builder's and engineer's knowledge, their responsibility to respond to correctly.

Resale and renovation. A future renovator or buyer who knows the soil classification of a property can make informed decisions about extension footings, landscaping that affects soil moisture and structural modifications. A property without soil classification documentation relies on investigation or assumption.

Australian soil classification classes explained

ClassNameSoil behaviourCharacteristic movementWhat it means for footings
Class AStable, non-reactiveSand, rock or dry areas with minimal moisture changeLess than 20mm surface movementStandard footing system, lowest footing cost
Class SSlightly reactiveClay soils with slight reactivity20 to 40mm surface movementLight footing system, minor additional reinforcement over Class A
Class MModerately reactiveMedium clay or silt soils40 to 60mm surface movementStandard reactive clay footing, the most common classification in Australian capital cities
Class H1Highly reactiveHigh clay content soils60 to 75mm surface movementMore robust footing, deeper beams, additional reinforcement
Class H2Highly reactiveVery high clay content soils75 to 100mm surface movementSignificantly more robust footing, substantial cost premium over Class M
Class EExtremely reactiveExtremely high clay content or problem soilsGreater than 100mm surface movementEngineered footing solution required, significant cost premium
Class PProblem siteFilled sites, soft soils, collapsing soils, soils subject to inundation, highly variable soils, or any site not fitting other classificationsVariable and potentially severe movementIndividual engineering solution required, most expensive classification
Class: Class A
Name: Stable, non-reactive
Soil behaviour: Sand, rock or dry areas with minimal moisture change
Characteristic movement: Less than 20mm surface movement
What it means for footings: Standard footing system, lowest footing cost
Class: Class S
Name: Slightly reactive
Soil behaviour: Clay soils with slight reactivity
Characteristic movement: 20 to 40mm surface movement
What it means for footings: Light footing system, minor additional reinforcement over Class A
Class: Class M
Name: Moderately reactive
Soil behaviour: Medium clay or silt soils
Characteristic movement: 40 to 60mm surface movement
What it means for footings: Standard reactive clay footing, the most common classification in Australian capital cities
Class: Class H1
Name: Highly reactive
Soil behaviour: High clay content soils
Characteristic movement: 60 to 75mm surface movement
What it means for footings: More robust footing, deeper beams, additional reinforcement
Class: Class H2
Name: Highly reactive
Soil behaviour: Very high clay content soils
Characteristic movement: 75 to 100mm surface movement
What it means for footings: Significantly more robust footing, substantial cost premium over Class M
Class: Class E
Name: Extremely reactive
Soil behaviour: Extremely high clay content or problem soils
Characteristic movement: Greater than 100mm surface movement
What it means for footings: Engineered footing solution required, significant cost premium
Class: Class P
Name: Problem site
Soil behaviour: Filled sites, soft soils, collapsing soils, soils subject to inundation, highly variable soils, or any site not fitting other classifications
Characteristic movement: Variable and potentially severe movement
What it means for footings: Individual engineering solution required, most expensive classification

The critical distinction between H1 and H2: Both are classified as highly reactive but H2 sites have greater expected surface movement and require a more robust engineering response. A builder who uses an H1 footing specification on an H2 site is under-engineering the foundation, a defect that may not manifest for years but can cause significant structural cracking when it does.

What causes soil reactivity

Understanding why soils are reactive helps homeowners understand why the classification matters and what can change the effective classification of a site over time.

Clay mineral content

Reactive clays contain specific clay minerals, primarily montmorillonite and smectite, that have a crystalline structure that absorbs water molecules, causing the clay particles to expand. The higher the concentration of these minerals, the more reactive the soil.

Moisture change

Reactivity is driven by moisture change, not by moisture content alone. A clay site that stays consistently wet or consistently dry has limited movement. A clay site that cycles between wet and dry conditions, as most Australian residential sites do through seasonal variation, experiences the expansion and contraction that creates structural risk.

Tree roots and vegetation

Large trees extract significant moisture from surrounding soil, creating localised drying and shrinkage that can cause differential movement under footings. Removing a large tree near an existing footing can cause the reverse, rehydration and expansion. Both can cause structural movement.

Drainage and water management

Poor site drainage that allows water to pond near the building can cause localised wetting and expansion. Leaking pipes under or near the slab can cause similar effects. Good drainage design and regular inspection of below-slab services are important maintenance considerations on reactive sites.

Landscaping

Garden beds against the house that are regularly watered, lawn irrigation systems and paving that directs water toward the building can all increase moisture variation under the footing, increasing effective site reactivity beyond what the classification assumed.

Soil classification by location in Australia

LocationDominant soil typeTypical classificationNotes
Sydney eastern suburbs and lower north shoreHawkesbury SandstoneClass A to Class SRock or sandy soil, low reactivity. Footing into rock common in some areas
Sydney inner west, south and southwestClay soilsClass M to Class H1Reactivity increases further west and south
Sydney hills district and outer westReactive clayClass H1 to Class H2Some of the most reactive soils in the Sydney basin
Melbourne inner suburbsBasalt and clayClass M to Class H1Variable, some areas on rock, others on reactive clay
Melbourne southeast, eastern and outer suburbsReactive clayClass H1 to Class H2Among the most reactive residential soils in Australia
Melbourne western suburbsBasalt rock and clayClass A to Class H1Variable, basalt rock in some areas, reactive clay in others
Brisbane north and inner suburbsWeathered rock and clayClass M to Class H1Variable by suburb
Brisbane south and southwestReactive clayClass H1 to Class H2Higher reactivity than inner Brisbane
Gold Coast coastal plainSand and alluvial soilsClass A to Class S, coastal. Class P possible near waterwaysSandy coastal soils are low reactivity, canal-front sites may have soft alluvial conditions requiring Class P engineering
Perth coastal plain (Bassendean Sand)SandClass AVery low reactivity, low bearing capacity requires engineered footings despite low reactivity
Perth limestone ridgeTamala LimestoneClass A, but requires drillingRock footing common, drilling required. Low reactivity but specialist footing
Perth eastern suburbs and hillsClayClass M to Class H1Reactivity increases further east
Adelaide plainsClayClass H1 to Class H2Highly reactive soils across significant parts of the Adelaide plains
CanberraClay and graniteClass M to Class H2Cold climate increases moisture variation, reactive clay performance can be more severe
Location: Sydney eastern suburbs and lower north shore
Dominant soil type: Hawkesbury Sandstone
Typical classification: Class A to Class S
Notes: Rock or sandy soil, low reactivity. Footing into rock common in some areas
Location: Sydney inner west, south and southwest
Dominant soil type: Clay soils
Typical classification: Class M to Class H1
Notes: Reactivity increases further west and south
Location: Sydney hills district and outer west
Dominant soil type: Reactive clay
Typical classification: Class H1 to Class H2
Notes: Some of the most reactive soils in the Sydney basin
Location: Melbourne inner suburbs
Dominant soil type: Basalt and clay
Typical classification: Class M to Class H1
Notes: Variable, some areas on rock, others on reactive clay
Location: Melbourne southeast, eastern and outer suburbs
Dominant soil type: Reactive clay
Typical classification: Class H1 to Class H2
Notes: Among the most reactive residential soils in Australia
Location: Melbourne western suburbs
Dominant soil type: Basalt rock and clay
Typical classification: Class A to Class H1
Notes: Variable, basalt rock in some areas, reactive clay in others
Location: Brisbane north and inner suburbs
Dominant soil type: Weathered rock and clay
Typical classification: Class M to Class H1
Notes: Variable by suburb
Location: Brisbane south and southwest
Dominant soil type: Reactive clay
Typical classification: Class H1 to Class H2
Notes: Higher reactivity than inner Brisbane
Location: Gold Coast coastal plain
Dominant soil type: Sand and alluvial soils
Typical classification: Class A to Class S, coastal. Class P possible near waterways
Notes: Sandy coastal soils are low reactivity, canal-front sites may have soft alluvial conditions requiring Class P engineering
Location: Perth coastal plain (Bassendean Sand)
Dominant soil type: Sand
Typical classification: Class A
Notes: Very low reactivity, low bearing capacity requires engineered footings despite low reactivity
Location: Perth limestone ridge
Dominant soil type: Tamala Limestone
Typical classification: Class A, but requires drilling
Notes: Rock footing common, drilling required. Low reactivity but specialist footing
Location: Perth eastern suburbs and hills
Dominant soil type: Clay
Typical classification: Class M to Class H1
Notes: Reactivity increases further east
Location: Adelaide plains
Dominant soil type: Clay
Typical classification: Class H1 to Class H2
Notes: Highly reactive soils across significant parts of the Adelaide plains
Location: Canberra
Dominant soil type: Clay and granite
Typical classification: Class M to Class H2
Notes: Cold climate increases moisture variation, reactive clay performance can be more severe

These are indicative ranges only. Soil conditions vary significantly at a suburb and lot level. A site-specific geotechnical investigation is always required, do not assume your site matches the general area description.

How soil classification affects footing design and cost

Soil classTypical footing systemApproximate cost premium over Class ANotes
Class ASimple strip footing or standard slabBaseline, no premiumSand, rock or non-reactive soil
Class SSlightly reinforced slab$2,000 to $5,000Minor additional reinforcement
Class MWaffle pod slab or reinforced strip footing$5,000 to $15,000Standard reactive clay response, most common in capital cities
Class H1Stiffened raft slab with deeper edge beams$15,000 to $30,000More substantial beam depth and reinforcement
Class H2Heavily stiffened raft slab with significantly deeper beams and additional reinforcement$25,000 to $50,000Significant engineering response required
Class EIndividual engineering design, typically deep strip footings or piers$40,000 to $100,000+Highly variable, depends on specific site conditions
Class PIndividual engineering design, piers, piles or engineered slab system$30,000 to $150,000+Most variable, filled sites, soft soils and waterway-adjacent sites have the highest variability
Soil class: Class A
Typical footing system: Simple strip footing or standard slab
Approximate cost premium over Class A: Baseline, no premium
Notes: Sand, rock or non-reactive soil
Soil class: Class S
Typical footing system: Slightly reinforced slab
Approximate cost premium over Class A: $2,000 to $5,000
Notes: Minor additional reinforcement
Soil class: Class M
Typical footing system: Waffle pod slab or reinforced strip footing
Approximate cost premium over Class A: $5,000 to $15,000
Notes: Standard reactive clay response, most common in capital cities
Soil class: Class H1
Typical footing system: Stiffened raft slab with deeper edge beams
Approximate cost premium over Class A: $15,000 to $30,000
Notes: More substantial beam depth and reinforcement
Soil class: Class H2
Typical footing system: Heavily stiffened raft slab with significantly deeper beams and additional reinforcement
Approximate cost premium over Class A: $25,000 to $50,000
Notes: Significant engineering response required
Soil class: Class E
Typical footing system: Individual engineering design, typically deep strip footings or piers
Approximate cost premium over Class A: $40,000 to $100,000+
Notes: Highly variable, depends on specific site conditions
Soil class: Class P
Typical footing system: Individual engineering design, piers, piles or engineered slab system
Approximate cost premium over Class A: $30,000 to $150,000+
Notes: Most variable, filled sites, soft soils and waterway-adjacent sites have the highest variability

These are indicative premiums for a standard 200 to 250 square metre single storey home. Multi-storey homes, larger floor plates and sites with additional complicating factors, slope, groundwater, acid sulfate soils, will have higher footing costs at every classification level.

How to get a soil classification for your site

A soil classification is determined by a geotechnical investigation, a soil test, conducted by a geotechnical engineer or geotechnical testing company. The investigation involves drilling or excavating test holes or borings to extract soil samples at defined depths, laboratory testing of the samples to determine clay mineral content and plasticity index, and preparation of a geotechnical report including the AS 2870 soil classification for the site.

When to commission a soil test

Ideally before design commences, so the structural engineer can design the footing system for the correct soil classification from the outset rather than redesigning after the test result is received. At minimum, a soil test should be completed before the building contract is signed, so the contract price reflects the actual footing requirement for the site's soil classification rather than an assumed or standard specification.

What a soil test costs

A standard residential soil test in Australia typically costs $800 to $2,500 depending on the number of test holes, the depth of investigation required and the location. This is among the most cost-effective investigations available relative to the financial risk it manages, a $1,500 soil test that reveals a Class H2 site allows the footing system to be correctly designed before the contract is priced, avoiding a variation of $25,000 or more during construction. See the companion guide Cost to Build a House in Australia for the complete cost framework.

Who conducts the soil test

Geotechnical engineers and geotechnical testing companies conduct soil investigations. Your architect, building designer or structural engineer can recommend a suitable firm for your site. Some volume builders include a soil test as part of their pre-construction process, confirm what is included and request a copy of the full report.

Reading your soil report, what to look for

Confirm the soil classification is stated clearly, Class A, S, M, H1, H2, E or P under AS 2870

Confirm the report is site-specific, prepared for your specific lot address and based on test holes conducted on your site

Check the number and depth of test holes, a single shallow test hole may not be representative of the full site. Confirm the investigation depth is appropriate for the proposed footing system

Check for any additional site conditions noted, groundwater, acid sulfate soils, fill material, tree root influence or other factors that affect the footing design beyond the basic classification

Confirm the report has been provided to the structural engineer, the structural engineer uses the classification to design the footing system. Confirm this has occurred before the footing design is finalised

Check whether the classification is uniform across the site or variable, a site with variable classification may require additional investigation in specific areas

Confirm the report date, a soil test conducted more than two to three years before construction may not reflect current conditions if significant vegetation changes, fill placement or drainage works have occurred on the site since the test

Confirm the report is available for your builder and structural engineer, request a copy for your own records

Soil classification and the building contract

The soil classification has a direct financial relationship with the building contract. Volume builders frequently include a standard footing specification in their contract, typically designed for Class M conditions, and include a provisional sum or allowance for site conditions. If the soil test reveals a higher classification than assumed, the provisional sum is exceeded and the homeowner pays the difference as a variation.

This is one of the most common and avoidable cost surprises in residential construction. Eliminating it requires:

  • Commissioning the soil test before the building contract is signed
  • Confirming the contract footing specification matches the actual soil classification
  • Eliminating or minimising the provisional sum for site conditions by pricing the actual footing requirement

For custom homes, the structural engineer designs the footing system from the soil test result, the building contract price should reflect the actual footing design, not an assumed standard specification. See How to Research a Builder Before Signing a Contract for the complete pre-contract framework.

Red flags relating to soil classification

Builder proposes a standard footing specification without confirming the soil classification first
Soil test has not been conducted before the building contract is signed, provisional sum used instead of actual footing specification
Builder is unaware of the soil classification applicable to your site despite it being available
Structural engineer has not been provided with the soil test report before designing the footing system
Volume builder includes a very low provisional sum for site conditions, insufficient to cover an H1 or H2 footing on a reactive clay site
Soil test was conducted by the builder's preferred testing company with results that appear more favourable than neighbouring properties, independent verification may be warranted
Single shallow test hole used on a large or irregular site, inadequate investigation for site variability
No mention of additional factors such as groundwater, acid sulfate soils or fill on sites where these are likely
Builder proceeds to slab pour before the soil test result is received and the structural engineer has confirmed the footing design is appropriate

BUILTLY and lasting project records

Soil classification is one of the most practically important pieces of site-specific information for any completed home, and one of the least likely to be preserved after construction is complete. A future owner, renovator or insurer who knows the soil classification of a property can make informed decisions about structural modifications, landscaping and maintenance. A property without this documentation relies on a new investigation or assumption.

BUILTLY is building a record of completed Australian homes that credits the builder, architects, designers and trades behind each one.

Frequently asked questions

What is soil classification in Australia?

Soil classification in Australia is a system defined under Australian Standard AS 2870, Residential Slabs and Footings, that categorises building sites according to the reactivity of the soil. Reactive soils, clays that expand when wet and contract when dry, require more robust footing systems to prevent structural movement from cracking footings, slabs and walls. The classifications range from Class A (stable, non-reactive) through Class S, M, H1, H2 and E (increasingly reactive) to Class P (problem sites requiring individual engineering solutions). The classification determines the minimum footing system design requirements and has a direct effect on construction cost.

What does Class M soil mean in Australia?

Class M, moderately reactive, is the most common soil classification in Australian capital cities. It describes clay or silt soils that exhibit moderate reactivity, expanding and contracting with moisture changes in a way that requires a reactive clay footing system but does not require the more substantial engineering responses needed for Class H1, H2 or E sites. A Class M site typically requires a waffle pod slab or reinforced strip footing rather than the standard slab used on Class A or Class S sites. The cost premium over a Class A footing is typically $5,000 to $15,000 for a standard residential home depending on the specific design and floor area.

What is the difference between Class H1 and Class H2 soil?

Both Class H1 and Class H2 are classified as highly reactive soils but they differ in the expected magnitude of surface movement. Class H1 sites have expected surface movement of 60 to 75mm, requiring a stiffened raft slab with deeper edge beams than a Class M footing. Class H2 sites have expected surface movement of 75 to 100mm, requiring a significantly more robust footing system with deeper beams, additional reinforcement and a substantially higher construction cost. Using an H1 footing specification on an H2 site is under-engineering the foundation, a defect that may not manifest for years but can cause significant structural cracking when seasonal moisture variation creates the full extent of movement the site is capable of.

What does Class P soil mean and how does it affect construction?

Class P, problem site, is the classification applied to sites that do not fit the standard reactive clay classifications. Class P sites include filled sites, soft or compressible soils, collapsing soils, sites subject to inundation or waterlogging, highly variable sites where soil conditions change significantly across the lot and sites with other problematic conditions. Class P requires an individual engineering solution, there is no standard footing system. The structural engineer designs a specific foundation response for the site conditions, which may involve deep strip footings, pier and beam systems, piles or a specially engineered slab. Class P footing costs are the most variable of any classification and can range from $30,000 to $150,000 or more above a standard footing depending on the specific site conditions.

Do I need a soil test before building in Australia?

Yes, a soil test is essential before designing or pricing any residential building project in Australia. The soil classification determined by the test is used by the structural engineer to design the footing system. Without a soil test, the footing system is designed on an assumed classification, typically Class M, which may be incorrect for the actual site. If the actual classification is higher than assumed, the footing system is under-engineered and the structural risk falls on the homeowner. If the building contract has already been signed with a standard footing specification and a provisional sum for site conditions, a higher-than-assumed classification results in a significant variation cost. Commissioning the soil test before the building contract is signed eliminates both risks.