Carpentry defects are among the most visible quality issues in new residential buildings in Australia. Unlike plumbing or electrical defects that are often concealed within walls and floors, carpentry defects are immediately apparent (in the gaps between skirting and floor, the inconsistent reveals around doors, the staircase that squeaks, the wardrobe doors that do not align). This visibility makes carpentry quality one of the most reliable proxies for overall construction standard, and one of the most common sources of defect claims during the contractual defects liability period.
This guide covers the frame and structural defects that set the conditions for everything that follows, the internal finishing defects most owners notice first, the external and weatherboard work that is exposed to weather, and the moisture and timber-movement defects that emerge over the first months after handover. Specific tolerances and Australian Standard provisions named below should be verified against the contract specification, the current edition of the Australian Standard and the relevant industry tolerance guide (such as the Master Builders / HIA Guide to Standards and Tolerances) for your project.
Why carpentry issues occur in new builds
Carpentry defects in new residential construction arise from failures at two distinct stages (first fix and second fix), each with different causes and different consequences. Understanding what carpenters do and the distinction between first and second fix provides essential context.
First fix failures
First fix carpentry (the structural timber frame, door frames and window frames installed before linings) creates the conditions for every subsequent carpentry issue. A frame that is out of plumb, door frames that are not square and structural members that are undersized or incorrectly positioned create cascading problems through every subsequent trade. Plasterboard cannot be fixed flat to an out-of-plumb frame. Doors cannot be hung correctly in an out-of-square frame. Skirting boards cannot sit flat against a wall that is not plumb. First fix failures are often not apparent until the second fix stage, when their consequences become visible. Understanding what happens at each stage of building a home clarifies why the frame stage inspection is a mandatory hold point, and why checking framing before linings is the most cost-effective quality control measure available. A thorough building inspection at the frame stage identifies these issues before they become costly to rectify.
Second fix failures
Second fix carpentry (internal doors, skirting, architraves, staircase installation and joinery installation) is performed under programme pressure at the end of the construction timeline, when the builder is managing multiple trades simultaneously and the handover deadline is approaching. Under this pressure, the precision required for consistent reveals, tight skirting mitres and smooth door operation is frequently compromised. Second fix defects are highly visible and have a significant impact on the perceived quality of the finished home.
Frame and structural carpentry defects
Frame-stage defects sit upstream of almost every other carpentry issue in the completed home and are also the hardest to rectify once linings are installed. The most consequential categories are wall frame plumb and racking issues, floor frame deflection and squeak, and roof frame alignment and bracing inadequacy. Australian Standards including AS 1684 (Residential timber-framed construction) and AS 1720 (Timber structures), together with AS 4055 for wind classification, set the design framework; the operative provisions for any specific project depend on the current edition of those standards and the project-specific wind classification and design loads. Verify the operative requirements with the project's structural engineer or building consultant rather than relying on generic numbers.
Wall frame plumb and racking
A visible lean in a wall, or diagonal cracking patterns in plaster that consistently track from corners, often signal underlying frame plumb or bracing issues rather than isolated finish problems. The defect typically originates at frame stage and is masked by the linings. The most reliable detection point is the pre-lining inspection; after lining, the assessment usually requires an experienced building consultant, raking light and (in significant cases) selective opening of linings.
Floor frame: squeak, bounce and level
Floor squeak under foot traffic typically reflects inadequate fixing between joist, bearer and flooring, or movement between sheet flooring and the supporting frame. Bounce or deflection reflects undersized members for the span and load, or joist spacing that does not suit the flooring. Level variation across a room often shows as a sloped surface visible when a ball is rolled across the floor and is most pronounced at room junctions. Where the defect is uniform across the home, the cause is generally a frame-stage issue; isolated cases are more often fixing-related.
Roof frame: truss spread, ridge sag and member alignment
Roof framing defects often present as a visible sag in the ridge line, a wave in the roof when viewed against a straight line at the eave, or internal cracking at the top of internal walls where the truss bottom chord has deflected. Where any of these signs are visible, the assessment should be escalated promptly to a structural engineer. Truss spread or significant ridge sag is not a cosmetic defect.
For broader detection methodology and the structural defect cluster, see the BUILTLY guide on the most common structural defects in new builds in Australia. Where a frame defect is suspected, escalation to a structural engineer is the appropriate next step rather than reliance on the builder's own assessment.
Common carpentry issues by location
| Location | Common issue | Cause | How it manifests |
|---|---|---|---|
| Internal doors throughout | Door sticks or drags on floor or frame | Frame out of square at rough-in stage, or door hung incorrectly at second fix | Door requires force to open or close; dragging sound or mark on floor |
| Internal doors throughout | Door swings open or closed of its own accord | Frame not plumb; door hangs unevenly | Door drifts open or closed when released; does not stay in chosen position |
| Internal doors throughout | Inconsistent reveals around door frame | Architrave positioned inconsistently or frame not plumb | Reveal wider on one side than the other, or at head compared to sides |
| Skirting boards throughout | Gap between skirting and floor | Floor not level, or skirting not scribed to floor | Visible gap at floor line; wider at one end than the other |
| Skirting boards throughout | Gap between skirting and wall | Wall not plumb, or skirting not tight against the wall face | Visible gap between the back of the skirting and the wall surface |
| Skirting boards throughout | Poor mitres at corners | Mitre not cut accurately, or walls not at 90 degrees | Visible gap at the mitre joint; open joint that allows light through |
| Staircase | Movement or bounce underfoot | Treads not adequately fixed to stringers, or stringers not adequately supported | Staircase moves or deflects under foot traffic |
| Staircase | Squeaking under foot traffic | Tread-to-riser or tread-to-stringer rubbing as the staircase flexes | Squeak or creak with each step; often worse in dry weather as timber shrinks |
| Staircase | Balustrade movement | Balustrade posts not adequately secured to stringer or floor | Balustrade moves or rocks when pressure is applied (safety risk) |
| Joinery (kitchen and wardrobes) | Cabinet doors and drawers not aligned | Joinery not levelled during installation, or carcass racking under load | Doors and drawers do not align; uneven gaps between adjacent doors |
| Joinery (kitchen and wardrobes) | Cabinet doors and drawers not operating smoothly | Hardware incorrectly adjusted at installation | Doors and drawers stiff, binding or not closing fully |
| Roof structure | Ceiling not flat (visible ripple or wave) | Ceiling joists or trusses not level, or plasterboard fixed to out-of-level framing | Undulating ceiling surface visible under raking light |
Door issues: the most common complaint
Door issues are the single most common carpentry complaint in new Australian homes, and one of the most avoidable. Most door problems originate in the first fix stage and are amplified by the second fix installation.
Out-of-square door frames
A door frame that is not square (with opposite corners at different dimensions) will produce a door that does not fit correctly regardless of how carefully it is hung. The door will either bind at a corner, have an inconsistent gap around the perimeter or require the leading edge to be planed to fit. Out-of-square frames should be identified and corrected at the frame inspection, before linings are installed.
Out-of-plumb frames
A door frame that is not plumb (tilting slightly forward, backward or sideways) will produce a door that swings open or closed of its own accord under gravity. Frames can be checked for plumb at the frame inspection using a spirit level. The tolerance considered acceptable is set by the contract specification and the relevant industry tolerance guide; any frame outside that tolerance should be corrected before lining commences.
Hanging quality
Even in a square and plumb frame, a door hung with inconsistent reveals (wider on one side than the other, or at the top than at the latch side) looks poorly finished. The reveal should be consistent on both sides and at the top of every door in the home. Inconsistent reveals indicate that the carpenter did not maintain a consistent hanging technique. Verify the tolerance considered acceptable against the contract specification and the operative industry tolerance guide.
Staircase issues: the highest safety consequence
Staircase defects carry the highest safety consequence of any carpentry issue in a new home. A staircase with structural movement, inadequate balustrade fixing or non-compliant spindle spacing is not just an aesthetic defect; it is a safety risk. The structural engineer's pre-construction checks should include staircase structural requirements.
NCC requirements for staircases
The National Construction Code (Volume Two for Class 1 and 10 buildings) sets minimum requirements for residential staircases covering balustrade height (measured from the tread nosing), maximum spindle or opening dimensions intended to prevent children becoming trapped, the permitted range for tread rise and going, and a requirement for a continuous, grippable handrail from bottom to top. The specific numerical values are amended through successive NCC editions; verify the current values against the edition published on the Australian Building Codes Board website for the project. Any staircase that does not comply with the current NCC residential requirements is a building code defect, not just an aesthetic issue.
Structural staircase issues
A staircase that moves or deflects under foot traffic indicates inadequate structural fixing (treads not adequately secured to stringers, stringers not adequately supported from below, or connections to the floor and landing not correctly made). Structural staircase issues should be rectified before handover; they are not cosmetic defects and the safety consequence is significant.
Skirting and architrave issues
Skirting boards and architraves are the finish elements that most directly signal second fix carpentry quality to anyone walking through the home. Gaps, poor mitres and inconsistent reveals are among the most commonly observed defects in new homes and the most difficult to accept given that they are visible in every room.
Skirting gaps at the floor
Skirting boards should sit flat on the floor with no visible gap. Gaps at the floor line indicate that the floor is not level (a first fix issue) or that the skirting was not scribed to the floor surface. On concrete slab floors, minor irregularities in the floor are common and the carpenter should scribe the skirting to the floor rather than leaving a gap. On timber floors, the floor should be levelled before skirting is installed.
Skirting gaps at the wall
Gaps between the back of the skirting and the wall indicate that the wall is not plumb (a first fix issue) or that the skirting was not forced against the wall and adequately fixed. Well-fixed skirting should have no visible gap between the timber and the plaster surface.
Mitre quality
The mitre joint at skirting and architrave corners (where two pieces of moulding meet at an internal or external corner) is one of the most visible quality indicators in second fix carpentry. A tight mitre with no visible gap or daylight through the joint indicates precise cutting. An open mitre indicates that the walls are not at a true 90 degrees, the mitre was cut inaccurately, or the moulding was not adequately sprung into the corner.
Internal finishing carpentry defects
Beyond the door, staircase and skirting categories above, internal finishing carpentry covers window reveal alignment, internal trim consistency, the interface between carpentry and cabinetry, and the broader finish-grade carpentry that is most readily compared between an apprentice-led and a trade-grade job.
Window reveals and internal trim
Window reveal alignment is a common defect category that is rarely surfaced in pre-handover walk-throughs because attention sits with the door reveals. Internal window reveals should be flush with the surrounding wall, square at corners, with consistent margins to the architrave. Gaps between the reveal and the architrave, or visible distortion where the reveal has been forced to an out-of-square opening, are typical defect markers. Internal trim consistency (the profile, finish and joint quality across architraves, skirting and any cover moulds) is the test of whether the second fix carpenter has worked to a consistent specification or has substituted product mid-job.
The carpentry-cabinetry interface
Where carpentry meets cabinetry (typically at wardrobes, built-in shelving, kitchen end panels and laundry joinery), the defect category often spans both trades. A common pattern is a scribed end panel that does not sit flat against an out-of-plumb wall, or an architrave that has been cut around a cabinet rather than the cabinet being set to the architrave. The responsibility allocation between the builder, the carpenter and the cabinetmaker is contract-specific, and disputes during the DLP often turn on it. See the BUILTLY guides on common cabinetry mistakes in new builds and on what to check in cabinetry before handover for the cabinetry-side checks that align with the carpentry-side issues raised here.
Tolerance expectations
Specific tolerance expectations for internal finishing carpentry are set by the contract specification, the relevant industry tolerance guide (commonly the Master Builders / HIA Guide to Standards and Tolerances) and, where applicable, the architect's documentation. There is no single Australian Standard that prescribes a universal numeric tolerance for every internal finishing element; the operative tolerance is the one named in the project documentation. Where the documentation is silent, the operative reference is the relevant industry guide for the current edition, and reasonable workmanship is the residual standard.
External carpentry and weatherboard defects
External carpentry sits in a more demanding service environment than internal work. The most common defect categories are weatherboard exposure and fixing pattern, soffit and eaves alignment, external trim and barge boards, and the carpentry portion of deck and pergola structures. Weather exposure, ultraviolet and moisture cycling drive the timber-treatment requirement and the durability outcome.
Weatherboards, soffits and trim
Weatherboard defects most commonly appear as uneven exposure between successive boards (the gap is not consistent), inconsistent fixing pattern (visible nails out of line or at differing depths), or poor jointing at scarf joints and at corners. Where the cladding sits over a battened cavity, the cavity must be free to drain; battens that bridge the drainage path or that obstruct the bottom of the cavity are a defect category in their own right. Soffit and eaves alignment should be consistent across the home, with no visible kick at the junction with the wall or the fascia. External trim and barge boards should sit straight against a straight reference line.
Decks, pergolas and timber treatment
Deck framing and pergola carpentry sit in the most exposed position on most residential projects. The principal carpentry defect categories are inadequate post-to-bearer connection, joist spacing inappropriate for the deck board specification, and inadequate provision for movement. The timber treatment specification for external use is generally a higher hazard class than internal framing; the operative class depends on the application (above-ground exposed, in-ground, marine) and is set by AS 1604 and the project specification. Verify the specified hazard class against the AS 1604 framework, the contract documentation and the manufacturer's product specification rather than relying on a generic figure. Where the deck is suspended over habitable space below, the waterproofing detail at the deck-to-wall junction is critical and is treated in the BUILTLY guide on waterproofing in Australia.
Moisture and timber movement defects
Timber is hygroscopic: it absorbs and releases moisture in response to the ambient environment and changes dimension as it does. A degree of post-installation movement is expected on every timber-framed build, and not every gap that opens after handover is a defect. Distinguishing normal seasonal movement from a defect of installation or material selection is the practical question, both at the end-of-period inspection and during the contractual DLP.
What is normal versus what is a defect
Hairline gap development at skirting mitres over the first months after handover, slight movement at architrave joints and minor shrinkage cracks at the junction of timber and other materials are typical seasonal movement on a newly completed timber-framed home. Significant gap development (wide enough to admit a coin into the joint), progressive cupping or warping of skirting and architrave, or movement that continues to widen across successive seasons indicates a defect rather than seasonal movement. The distinction generally turns on the magnitude, the pattern (uniform across the home versus isolated) and the trajectory (settling versus continuing to widen).
Cause distinction: timber moisture content versus building movement
The three principal cause categories are timber installed at a moisture content too high for the in-service environment (the timber dries in-place and shrinks), timber exposed to site moisture during construction (lock-up before linings dry, water ingress through unprotected openings), and broader building movement reflecting slab, frame or foundation behaviour. The first two are carpentry-side cause categories; the third sits in the structural framework and may overlap with the categories in the BUILTLY guide on common structural defects in new builds. Subfloor ventilation, where the build has a suspended floor, contributes to the moisture environment that the floor frame sits in and is worth confirming as part of a moisture-related defect assessment. Where plumbing-side moisture (an undetected leak, condensation on uninsulated pipework) is contributing, the relevant escalation is to the plumber as well as the builder; see the BUILTLY guide on common plumbing issues in new builds in Australia. Specific moisture-content percentages and acceptance thresholds are set by the relevant Australian Standards and the project specification; verify these for any specific project.
When to identify carpentry issues
Understanding what documents your builder must provide at each stage helps ensure inspection opportunities are not missed.
| Stage | What to check | How to check |
|---|---|---|
| Frame inspection (before linings) | All door frames plumb and square; measure diagonals to confirm squareness | Independent building inspector; spirit level and tape measure on every frame |
| Pre-lining inspection | Confirm all framing is plumb (walls, reveals, ceiling joists) | Independent building inspector; raking light reveals out-of-plumb and bowing |
| Lock-up (after external cladding and roof) | Roof framing, visible from roof space before insulation is installed | Independent building inspector |
| Pre-handover inspection | All doors, skirting, architraves, staircase, joinery (full second fix assessment) | Independent building inspector commissioned by homeowner |
| At handover (homeowner inspection) | Walk every room; check all doors operate, skirting joints, joinery alignment | Systematic room-by-room check at good lighting conditions |
| 3-month post-handover | Timber movement defects become apparent as the building dries; squeaking stairs, opening skirting mitres | Homeowner; report in writing to builder |
| End of defects liability period | All carpentry elements; confirm no movement-related defects have developed | Independent building inspector before the contractual DLP expires |
Pre-handover carpentry inspection checklist
Use this checklist alongside the BUILTLY guides on the building a house checklist and the final inspection checklist before handover for a comprehensive pre-handover assessment.
When to engage a building consultant
Where a DIY inspection surfaces suspected carpentry defects (particularly at frame stage, at handover, or during the contractual DLP), the question of whether to engage a qualified independent building consultant is generally a question of cost versus consequence. A consultant inspection costs materially less than the rectification of a frame defect after lining, and significantly less than the legal cost of contesting an unresolved defect after the DLP has closed.
A qualified building consultant assesses workmanship and material against the contract documentation, the Australian Standards and the relevant industry tolerance guide, and prepares a written report that is admissible at tribunal where the matter escalates. The consultant pathway is distinct from a structural engineer assessment: where the suspected defect is structural (truss spread, ridge sag, significant frame plumb issue, slab or foundation interaction), a structural engineer is the appropriate professional rather than a general building consultant. Where the suspected defect is finishing-grade (door reveals, skirting, joinery alignment), a building consultant is generally sufficient.
Timing matters. A frame-stage independent inspection costs least and identifies the most consequential category of defect; a pre-handover inspection identifies most second-fix defects before acceptance; an end-of-DLP inspection identifies movement-related defects before the contractual rectification mechanism expires. The three inspection points reinforce one another and are addressed in more detail in the BUILTLY guides on the final inspection checklist before handover, the building handover package and the defects liability period.
What to do if carpentry issues are not fixed
The builder's warranty framework and the disputes resolution process provide the broader context for escalating unresolved defects; the practical sequence is below.
Red flags
Warning signs in carpentry quality
- Multiple doors throughout the home sticking, dragging or swinging (indicates systematic framing quality issues rather than isolated installation errors).
- Skirting gaps consistent throughout the home rather than isolated (indicates out-of-plumb framing rather than individual installation errors).
- Staircase movement or balustrade movement identified at handover (structural issue that must be rectified before occupation).
- Builder attributes carpentry defects to "normal timber movement" without distinguishing seasonal movement from structural defect.
- Builder is unresponsive to written defect reports during the contractual DLP.
- Staircase non-compliance with current NCC residential requirements (building code violation, not just a defect).
- Ceiling waves or undulations visible under raking light (out-of-level framing that is difficult and expensive to rectify after linings).
- Visible wall frame lean, racking or cracking patterns in plaster at corners (potential bracing inadequacy).
- Builder unable to identify the timber grades or hazard-class treatments used in the frame.
- Visible green or high-moisture timber in framing at lining stage.
- Truss spread or visible ridge sag in the roof line.
- Refusal to allow an independent carpentry or building inspection.
BUILTLY and carpentry quality verification
Carpentry quality is one of the most visible indicators of overall construction standard in any completed home. The detail visible in completed project photography (skirting precision, door reveals, staircase quality, joinery alignment, external trim and weatherboard exposure) is one of the most reliable proxies for the standard a builder consistently delivers.
BUILTLY is building a record of completed Australian homes that credits the builder, designers and trades behind each one.
Frequently asked questions
What are the most common carpentry issues in new Australian homes?
The most common carpentry issues in new Australian homes are doors that stick, drag or swing of their own accord (typically caused by out-of-square or out-of-plumb door frames), inconsistent architrave reveals around door openings, skirting boards with visible gaps at the floor or back, poor mitre joints at corners, staircase movement and squeaking, and joinery doors and drawers that do not align or operate smoothly. Most of these issues originate in the first fix stage (in framing that is not plumb or square) and become visible in the second fix stage when their consequences appear in the finished work.
How do I check for carpentry defects before handover?
Open and close every internal door, checking for sticking, dragging and self-swinging. Check the reveal around all four sides of every door for consistency. Check skirting boards for gaps at the floor and wall, and for tight mitres at corners. Walk the full staircase, checking for movement, bounce and squeaking, and verify balustrade height, spindle spacing and tread dimensions against the current National Construction Code residential requirements. Open all kitchen and wardrobe doors and drawers. Check ceiling flatness under raking light from room corners. Commissioning an independent building inspector for a formal pre-handover inspection is the most reliable way to identify defects an untrained eye misses.
Are carpentry defects covered by the builder's warranty in Australia?
Carpentry defects that result from defective workmanship or materials sit within the contractual defects liability period (DLP) defined by the building contract and, separately, within the statutory warranty regime that each state and territory provides for residential building work. The DLP is the contractual rectification mechanism that runs from practical completion; the statutory warranty regime is longer and operates regardless of the contract. The specific periods, defect categories and escalation pathways vary by jurisdiction and should be verified against the current legislation. See the BUILTLY guides on the defects liability period and builder warranties for the full framework.
What is the correct reveal for internal doors in a new home?
Internal door reveals (the gap between the door edge and the door frame) should be consistent on both sides and at the head of the door across every door in the home. A reveal that is materially wider on one side than the other, or that varies noticeably from door to door, indicates either an out-of-square frame or inconsistent hanging technique. The specific tolerance considered acceptable varies between contract specifications and industry guidelines such as the Master Builders / HIA Guide to Standards and Tolerances; verify the operative tolerance for your project against the contract specification and the current edition of the relevant industry guide.
What NCC requirements apply to staircases in new homes?
The National Construction Code Volume Two sets minimum requirements for residential staircases, including a minimum balustrade height measured from the tread nosing, a maximum spindle spacing intended to prevent children becoming trapped, defined ranges for tread rise and going, and continuous grippable handrails. Specific dimensional values are amended through successive NCC editions, so any specific number should be verified against the current edition published on the Australian Building Codes Board website rather than relied on from a guide. A staircase that does not comply with current NCC residential requirements is a building code defect, not just an aesthetic issue.