Advice

Setbacks and Building Envelope Rules in Australia Explained

Last updated: October 2026

Before an architect draws a single line on a residential design, the building envelope defines the three-dimensional space within which the building must fit. Setbacks - the required distances between the building and the property boundaries - define the horizontal limits. Height controls define the vertical limit. Site coverage maximums define how much of the site can be covered by buildings. Together these controls define the building envelope - the maximum volume that planning rules permit on any given site. Understanding setbacks and building envelope rules before you design or purchase a site is one of the most practically important steps in any residential construction or development project. This guide explains exactly what the rules are, how they vary across Australia and what to confirm before your architect begins.

What are setbacks?

A setback is the minimum distance required between a building or structure and a property boundary - the front boundary facing the street, the rear boundary at the back of the site or the side boundaries separating the site from neighbouring properties.

Setbacks are defined in the planning controls that apply to the site - typically in the state planning legislation, the local environmental plan or the development control plan administered by the local council. They vary by state, by local government area, by zone and sometimes by street or precinct.

Setbacks serve three primary purposes - they maintain a consistent streetscape character by ensuring buildings are set back from the street by a similar distance, they provide separation between buildings to allow for privacy, natural light, ventilation and access for maintenance and they protect the amenity of neighbouring properties by preventing buildings from being built hard against shared boundaries.

Types of setbacks

The following table summarises the most common setback types in Australian residential construction and their typical dimensions. As discussed in the companion guide Easements on Property in Australia, easement setbacks are additional to standard planning setbacks.

Setback typeWhat it measuresTypical residential dimensionState variation
Front setback - primary streetDistance from the primary street boundary to the front of the building4.5 to 9 metres depending on zone and street typeVaries significantly by council - some streets have character setbacks requiring specific distances
Front setback - secondary street - corner lotsDistance from the secondary street boundary on a corner lot2 to 4.5 metres typically - less than primary setbackVaries by council - corner lot controls differ from standard lots
Side setback - ground floorDistance from the side boundary to the ground floor wall900mm to 1.5 metres for standard residentialNSW SEPP Housing - 900mm for lots above 6 metres wide - Victoria ResCode - varies by lot width
Side setback - upper floorDistance from the side boundary to upper floor walls1.5 to 2 metres for upper floor levelsIncreases with building height in most states
Rear setbackDistance from the rear boundary to the rear of the building3 to 6 metres typically - varies by lot depth and zoneSome states allow rear setback averaging - check local controls
Garage setback - from streetDistance from the street boundary to the garage doorMinimum 5.5 metres in most states - to allow a car to park in the driveway without overhanging the footpathConsistent across most Australian states for safety reasons
Setback from easementsDistance from an easement boundary to a permanent structure1 metre from each side of easement pipe centreline typicallyVaries by easement type and holder requirements
Setback type

Front setback - primary street

What it measures

Distance from the primary street boundary to the front of the building

Typical residential dimension

4.5 to 9 metres depending on zone and street type

State variation

Varies significantly by council - some streets have character setbacks requiring specific distances

Setback type

Front setback - secondary street - corner lots

What it measures

Distance from the secondary street boundary on a corner lot

Typical residential dimension

2 to 4.5 metres typically - less than primary setback

State variation

Varies by council - corner lot controls differ from standard lots

Setback type

Side setback - ground floor

What it measures

Distance from the side boundary to the ground floor wall

Typical residential dimension

900mm to 1.5 metres for standard residential

State variation

NSW SEPP Housing - 900mm for lots above 6 metres wide - Victoria ResCode - varies by lot width

Setback type

Side setback - upper floor

What it measures

Distance from the side boundary to upper floor walls

Typical residential dimension

1.5 to 2 metres for upper floor levels

State variation

Increases with building height in most states

Setback type

Rear setback

What it measures

Distance from the rear boundary to the rear of the building

Typical residential dimension

3 to 6 metres typically - varies by lot depth and zone

State variation

Some states allow rear setback averaging - check local controls

Setback type

Garage setback - from street

What it measures

Distance from the street boundary to the garage door

Typical residential dimension

Minimum 5.5 metres in most states - to allow a car to park in the driveway without overhanging the footpath

State variation

Consistent across most Australian states for safety reasons

Setback type

Setback from easements

What it measures

Distance from an easement boundary to a permanent structure

Typical residential dimension

1 metre from each side of easement pipe centreline typically

State variation

Varies by easement type and holder requirements

What is a building envelope?

The building envelope is the three-dimensional volume defined by the combination of all planning controls that restrict the size, position and height of a building on a site. It is the maximum space within which the building must fit - not just in plan but in three dimensions.

The building envelope is defined by four primary controls working together:

  • Setbacks define the horizontal position of the building on the site - how far it must sit from each boundary.
  • Height limits define the maximum height of the building - typically expressed as a maximum number of metres above natural ground level or a maximum number of storeys.
  • Site coverage defines the maximum proportion of the site that can be covered by buildings and structures - typically expressed as a percentage of the total site area.
  • Floor space ratio - FSR defines the maximum total floor area of all buildings on the site expressed as a ratio to the site area. An FSR of 0.6:1 on a 600 square metre site allows a maximum of 360 square metres of total floor area across all levels.

Together these four controls define the building envelope - the volume of space available for the architect to work within. A site with generous setbacks, a high height limit, a high site coverage maximum and a high FSR has a large building envelope. A site with tight setbacks, a low height limit, a low site coverage maximum and a low FSR has a constrained building envelope that limits what can be built. Understanding these controls before committing to a site is essential - as discussed in the Pre-Construction Stage Explained guide.

Building envelope controls by element

The following table summarises the planning controls that together define the building envelope for a residential site in Australia.

ControlWhat it limitsWhere to find itTypical residential value
Front setbackHow close the building can be to the streetLocal Environmental Plan or Development Control Plan - council website4.5 to 9 metres depending on zone
Side setbackHow close the building can be to side boundariesState planning policy plus local DCP900mm to 2 metres depending on building height and lot width
Rear setbackHow close the building can be to the rear boundaryLocal DCP - council website3 to 6 metres - varies by lot depth
Maximum heightHow tall the building can beLocal Environmental Plan - council website8.5 to 12 metres for residential - some areas lower
Site coverageHow much of the site can be covered by buildingsLocal DCP - sometimes in LEP50 to 60 percent typically for residential
Floor space ratio - FSRMaximum total floor area relative to site areaLocal Environmental Plan0.5:1 to 0.8:1 for standard residential - varies widely
Landscaped area minimumMinimum proportion of site that must remain as soft landscapingLocal DCP20 to 35 percent typically
Solar access controlsShadow restrictions on neighbouring properties - particularly south facing neighboursState planning policy - SEPP in NSWVaries by state - NSW SEPP Housing has specific shadow diagrams requirements
Overshadowing limitsMaximum shadow cast on neighbouring properties at specified timesLocal DCP or state policyVaries - typically assessed at midwinter noon or 9am to 3pm
Control

Front setback

What it limits

How close the building can be to the street

Where to find it

Local Environmental Plan or Development Control Plan - council website

Typical residential value

4.5 to 9 metres depending on zone

Control

Side setback

What it limits

How close the building can be to side boundaries

Where to find it

State planning policy plus local DCP

Typical residential value

900mm to 2 metres depending on building height and lot width

Control

Rear setback

What it limits

How close the building can be to the rear boundary

Where to find it

Local DCP - council website

Typical residential value

3 to 6 metres - varies by lot depth

Control

Maximum height

What it limits

How tall the building can be

Where to find it

Local Environmental Plan - council website

Typical residential value

8.5 to 12 metres for residential - some areas lower

Control

Site coverage

What it limits

How much of the site can be covered by buildings

Where to find it

Local DCP - sometimes in LEP

Typical residential value

50 to 60 percent typically for residential

Control

Floor space ratio - FSR

What it limits

Maximum total floor area relative to site area

Where to find it

Local Environmental Plan

Typical residential value

0.5:1 to 0.8:1 for standard residential - varies widely

Control

Landscaped area minimum

What it limits

Minimum proportion of site that must remain as soft landscaping

Where to find it

Local DCP

Typical residential value

20 to 35 percent typically

Control

Solar access controls

What it limits

Shadow restrictions on neighbouring properties - particularly south facing neighbours

Where to find it

State planning policy - SEPP in NSW

Typical residential value

Varies by state - NSW SEPP Housing has specific shadow diagrams requirements

Control

Overshadowing limits

What it limits

Maximum shadow cast on neighbouring properties at specified times

Where to find it

Local DCP or state policy

Typical residential value

Varies - typically assessed at midwinter noon or 9am to 3pm

How setbacks vary across Australian states

Setback rules in Australia are not nationally consistent - they are set by state planning legislation and local council planning controls and vary significantly between states, between councils and sometimes between zones within the same council area.

New South Wales

In NSW, residential setbacks for complying development under the State Environmental Planning Policy - Housing are specified in the policy itself - providing a consistent statewide baseline. Front setbacks are typically 4.5 metres for a primary street and 2 metres for a secondary street. Side setbacks are 900mm for a single storey and 1.5 metres for a two storey element on lots above 6 metres wide. Rear setbacks are typically 3 metres for a single storey and 4 metres for two storey. Where a DA is required rather than CDC, local DCP setbacks apply and may differ from these standards. The Construction Certificate process confirms compliance with these controls.

Victoria

In Victoria, residential setbacks are governed by ResCode - Schedule 55 to the Planning and Environment Regulations. Front setbacks in ResCode are assessed against the average of the two neighbouring properties' setbacks - or 9 metres - whichever is the lesser. Side setbacks are 1.2 metres for a wall up to 3.6 metres in height, increasing with wall height. Rear setbacks depend on the wall height. ResCode provides a consistent Victorian baseline that can be varied by local planning policies.

Queensland

In Queensland, setbacks are set in each council's planning scheme. Brisbane City Council's setbacks differ from Gold Coast City Council's setbacks. The Queensland Planning Act 2016 provides the framework but the specific standards are local. The Gold Coast City Plan, for example, has specific setbacks for different lot sizes and zones that differ from Brisbane's.

Western Australia

In WA, the Residential Design Codes - R-Codes - provide statewide residential design standards including setbacks. The R-Codes set front setbacks, side setbacks, rear setbacks and lot boundary setbacks based on the density code of the site - R20, R40, R60 and so on. Higher density codes generally have reduced setback requirements.

Setback variations and concessions

Planning controls include mechanisms for varying standard setbacks - which is how buildings that appear to breach normal setback rules have been legitimately approved.

Variation through a development application

A development application can seek approval for a variation to the standard setback - arguing that the variation is justified by the site's specific circumstances, that the variation achieves the objectives of the setback control despite not meeting the standard dimension and that the variation does not unreasonably affect the amenity of neighbouring properties. Variations are not guaranteed - the assessing council makes a judgment on each application. The Private Certifier vs Council Approval guide explains the assessment pathways available.

Zero lot line development

Some planning schemes permit zero lot line development - where the building is built hard against one side boundary - in exchange for a larger setback on the other side. This allows efficient use of narrow lots while maintaining adequate light and ventilation across the site as a whole.

Balconies, eaves and minor projections

Most planning controls allow minor building elements to encroach into setback areas - eaves typically up to 600mm, balconies up to 1 metre on upper floors and bay windows in some schemes. These concessions are specified in the planning controls and vary by state and council.

How to find setback rules for your site

Council planning portal

Every Australian council publishes its planning controls online - typically through a planning portal or mapping tool where you can enter the property address and view the applicable zone, development controls and setback requirements. In NSW the Planning Portal at planningportal.nsw.gov.au provides access to LEP maps and DCP provisions. In Victoria the Planning Property Report at planning.vic.gov.au provides zone and overlay information. A site survey and contour survey provide the precise site data needed to apply these controls.

Engage the architect before purchasing

The most reliable way to understand what can be built on a site before purchasing is to engage an architect for a pre-purchase assessment - as discussed in the companion guide When to Engage an Architect in Australia. The architect reviews the planning controls, identifies the building envelope and provides a preliminary view of what can be designed within the constraints before you commit.

Pre-DA consultation

For complex sites or significant proposed variations to setback controls, most councils offer a pre-DA consultation service - a meeting with council planning staff to discuss the proposed development before a formal application is lodged. Pre-DA consultation provides early feedback on whether proposed setback variations are likely to be supported - reducing the risk of a refused DA. For sloped or constrained sites, the Building on a Sloped Block guide discusses the additional considerations.

Setbacks and envelope due diligence checklist

Use this checklist before purchasing a site or lodging a development application to confirm all setback and building envelope requirements have been identified and addressed. See also the Building a House Checklist for broader pre-construction due diligence.

Before purchasing any site - check the applicable zone and planning controls through the council planning portal

Identify the front, side and rear setback requirements for the site - and confirm whether the site is subject to any special character or heritage setback controls

Identify the maximum height limit, site coverage maximum and FSR - confirm these are consistent with the intended development

Check for any overlays - heritage, flood, bushfire, coastal - that may impose additional setback or height controls beyond the standard zone controls

Check for any easements on the title - easements impose additional setback requirements beyond planning setbacks

Confirm the building footprint in the proposed design is fully within all required setbacks before the DA is lodged

Confirm eave, balcony and minor projection encroachments into setback areas are within the permitted concessions for the applicable planning controls

If a setback variation is required - engage a town planner to assess whether the variation is supportable before committing to a design that depends on it

For corner lots - confirm both the primary street and secondary street setback requirements - they differ in most states

Confirm garage setback from street - minimum 5.5 metres in most states to allow off-street parking without overhanging the footpath

Red flags

Design has been prepared without confirming the applicable setback controls - architect assumed standard setbacks that may not apply to this site
Proposed building footprint encroaches within required setbacks - DA will be refused unless a variation is approved
Heritage or character overlay imposes additional setback requirements that have not been identified - design must be revised before lodgement
Garage is less than 5.5 metres from the street boundary - non-compliant in most states and will be identified at building permit stage
Corner lot secondary street setback has not been identified - buildings on corner lots have two street frontage setbacks
Site coverage calculation has not been conducted - proposed development may exceed the maximum permitted site coverage
FSR calculation has not been conducted on a constrained site - proposed floor area may exceed the maximum permitted FSR
Pre-purchase assessment was not conducted before purchasing a constrained site - setback controls may prevent the intended development

BUILTLY and lasting project records

BUILTLY is building a record of completed Australian homes that credits the builder, designers and trades behind each one.

Frequently asked questions

What are setbacks in residential construction in Australia?

A setback is the minimum required distance between a building and a property boundary - the front boundary facing the street, the rear boundary and the side boundaries. Setbacks are defined in state planning legislation and local council planning controls and vary by state, council and zone. Typical residential front setbacks range from 4.5 to 9 metres. Side setbacks are typically 900mm to 2 metres depending on building height and lot width. Rear setbacks are typically 3 to 6 metres. Buildings must comply with all applicable setbacks or obtain a variation approval through a development application.

What is a building envelope in residential construction?

A building envelope is the three-dimensional volume defined by the combination of all planning controls restricting the size, position and height of a building on a site. It is defined by setbacks - horizontal position - height limits - vertical extent - site coverage - proportion of the site that can be covered - and floor space ratio - maximum total floor area relative to site area. The building envelope defines the maximum space within which the architect must design. A constrained building envelope limits design options significantly - understanding the envelope before purchasing a site is essential for any development project.

How close can I build to my boundary in Australia?

The minimum distance from a boundary depends on the boundary type, the building height and the applicable state and local planning controls. In NSW under the SEPP Housing complying development pathway, the minimum side setback is 900mm for a single storey element on lots above 6 metres wide. In Victoria under ResCode, the minimum side setback is 1.2 metres for a wall up to 3.6 metres high. Rear setbacks are typically 3 to 6 metres. These are minimums - local council DCPs may require larger setbacks. Check the specific planning controls for your site through the council planning portal before designing.

Can setback rules be varied in Australia?

Yes - setback variations can be approved through a development application process where the applicant argues that the variation is justified by the site's specific circumstances and achieves the objectives of the control despite not meeting the standard dimension. Variations are not guaranteed - the council makes a judgment on each application. Some planning schemes also allow administrative variations for minor encroachments - a planning officer can approve minor setback variations without a full DA. Engage a town planner to assess whether a proposed variation is supportable before designing a project that depends on it.

How do I find the setback rules for my property in Australia?

Check the council planning portal for your local government area - enter the property address to view the applicable zone and development control plan provisions. In NSW use the NSW Planning Portal at planningportal.nsw.gov.au. In Victoria use the Planning Property Report at planning.vic.gov.au. For Queensland use your local council's online mapping tool. For WA check the applicable R-Code density for the site. For any site where the intended development is close to the setback limits or where variations may be required, engage an architect for a pre-purchase assessment or a town planner for a planning advice letter before committing to the site or the design.