Staircase design in Australian residential construction is governed by specific requirements under the National Construction Code - and getting them wrong has both safety and legal consequences. A staircase with insufficient balustrade height, excessive rise, inadequate going or non-compliant spindle spacing is not just a building defect - it is a building code violation that the building certifier should have identified and that the builder is obligated to rectify. Yet stair design non-compliance is one of the most commonly identified defects in pre-handover building inspections in Australia. This guide explains exactly what the NCC requires for residential staircases, what the most common compliance failures are and what to check before accepting the keys.
Why stair design rules matter
Stair design rules exist because staircases are one of the most common locations for serious injuries in residential buildings. Falls on stairs account for a significant proportion of residential fall injuries in Australia - and the design of the staircase directly affects the risk of those falls occurring. Balustrade height prevents falls from the side of the staircase. Rise and going dimensions affect how naturally and safely people move up and down the stairs. Handrail continuity and height provides support and arrest in the event of a stumble. Spindle spacing prevents children from becoming trapped between balustrade elements.
The NCC stair requirements are minimum safety standards - not design ideals. A staircase that just meets the minimum requirements is compliant but a well-designed staircase considers these requirements as a starting point and optimises the proportions, materials and detailing beyond the minimum.
NCC stair requirements - residential
| Stair element | NCC minimum requirement | Notes |
|---|---|---|
| Rise - vertical height of each step | Minimum 115mm - maximum 190mm | Adjacent rises and goings: maximum 5mm variation; maximum-to-minimum within a flight: 10mm, subject to NCC conditions |
| Going - horizontal depth of each tread | Minimum 240mm - maximum 355mm | Measured from nosing to nosing on successive treads |
| Rise plus going formula | Twice the rise plus the going must be between 550mm and 700mm | Ensures comfortable walking rhythm - 2R + G between 550 and 700 |
| Nosing - tread overhang | Confirm nosing detail against the applicable NCC and stair design | Excessive nosing creates a trip hazard |
| Stair width - minimum clear width | Confirm required clear width for the building class and access requirements | Measured between handrails or between a wall and a handrail |
| Balustrade height - from floor level | Minimum 1000mm above floor level at the top of the staircase and on landings | Applies to any floor level 1000mm or more above the ground or floor below |
| Balustrade height - from stair nosing | Minimum 865mm measured vertically from the nosing of the tread | Lower measurement applies along the rake of the staircase |
| Balustrade opening - spindle spacing | Prevent a 125mm sphere passing through, subject to stair-opening exceptions | Prevents a 125mm sphere from passing through - child safety |
| Balustrade climbability | For falls of 4m or more, no climb-facilitating elements in the 150–760mm zone | Lower barriers and wire infill need assessment against their applicable provisions |
| Handrail - height | At least 865mm above stair nosings for relevant housing stairs | Must be continuously graspable along full length |
| Handrail - continuity | Continuous from top to bottom of each flight - no gaps | Must be graspable from every point on the stair |
| Handrail - profile | Must provide a graspable handhold suited to the applicable provisions | Additional accessible-design requirements may apply; no universal profile range is stated here |
| Headroom | Minimum 2000mm measured vertically above stair nosing | Clear headroom throughout the full stair width |
Stair component definitions
| Component | Definition | Where it is on the staircase |
|---|---|---|
| Rise | The vertical height of one step - measured from the top of one tread to the top of the next | The vertical face of each step |
| Going | The horizontal depth of one tread - measured from nosing to nosing of consecutive treads | The horizontal surface of each tread |
| Nosing | The front edge of the tread - the point where the tread overhangs the riser below | The projecting front edge of each tread |
| Tread | The horizontal surface of a step - what you step on | The flat surface of each step |
| Riser | The vertical face of a step - the board connecting one tread to the next | The vertical face between treads - may be open in some designs |
| Stringer | The structural side member of the staircase - supports the treads and risers | The diagonal timber or steel member running along each side of the staircase |
| Balustrade | The barrier system along the open sides of the staircase and on landing edges - prevents falls | The full barrier system including posts, rails and infill elements |
| Baluster or spindle | An individual vertical infill element of the balustrade | The vertical elements between the top and bottom rails of the balustrade |
| Newel post | The structural post at the top and bottom of the balustrade - and at changes of direction | The principal vertical post at each end and corner of the balustrade |
| Handrail | The graspable rail at the top of the balustrade - or a separate rail on a wall | The continuous graspable rail along the staircase |
| Landing | A flat platform between flights of stairs or at the top or bottom of a staircase | The flat area between flights in a multi-flight staircase |
The rise and going formula
The rise and going formula is one of the most important stair design principles in the NCC - and one of the least understood by homeowners and builders.
For relevant housing stairs, twice the rise plus the going must be between 550mm and 700mm: 2R + G = 550–700mm. The rise and going must also satisfy their individual limits. Check the NCC edition adopted for the approval and the stair category; this is not a complete compliance checklist. Flights generally have 2–18 risers and must satisfy landing, slip resistance, open-riser and winder provisions where applicable.
Why it matters: A rise of 190mm and going of 240mm gives 2 × 190 + 240 = 620mm. Both individual dimensions and the formula are within the stated housing limits.
A rise of 175mm and going of 280mm gives 2 × 175 + 280 = 630mm, within the formula range.
Finding the right proportion: A rise of 165–175mm and going of 280–300mm gives 2R + G of 610–650mm. A going of 375mm or 400mm would exceed the stated 355mm maximum even if the formula alone were satisfied.
Balustrade requirements - what homeowners most commonly miss
The balustrade requirements are the stair element most commonly found non-compliant at pre-handover inspections - and the requirements most commonly misunderstood by both homeowners and builders.
Balustrade height - two measurements: The balustrade height has two distinct measurement points and both must be met. The 1000mm measurement applies from the floor level at the top of the staircase - the landing - and from any floor level 1000mm or more above the ground. The 865mm measurement applies from the nosing of any stair tread - measured vertically. Both measurements must be satisfied simultaneously. A balustrade that is 1000mm at the landing but drops below 865mm above the tread nosings when viewed along the rake of the staircase is non-compliant.
Spindle spacing - the 125mm rule: Relevant barrier openings must prevent a 125mm sphere from passing through. Stairway geometry has specific exceptions, including triangular openings at a tread, riser and bottom rail. Confirm the applicable test with the certifier.
Use the opening tests above during the pre-handover inspection, with a suitable check gauge rather than estimating gaps by eye.
Climbability - horizontal elements: For relevant housing barriers protecting a fall of 4m or more, elements between 150mm and 760mm above the floor must not facilitate climbing. Horizontal rails are not universally prohibited on lower barriers. Wire barriers also have specific tension, spacing and deflection requirements. Confirm the design with the certifier.
Common stair design mistakes
| Mistake | What it means | How to identify it | How to rectify |
|---|---|---|---|
| Inconsistent rise heights | Rise variation exceeds the applicable adjacent or whole-flight limits | Measure every rise with a tape measure | Recut and reinstall affected treads - structural remedy required if stringer heights are wrong |
| Balustrade below 865mm above tread nosings | Balustrade height is measured at the landing but drops below 865mm along the rake | Measure vertically from nosing of each tread to top of handrail | Raise balustrade height - may require replacing newel posts and handrail |
| Spindle spacing exceeds 125mm | A 125mm sphere passes through an opening subject to that test | Test with a 125mm gauge or sphere | Install additional spindles to reduce spacing |
| Horizontal balustrade elements - climbable | Climb-facilitating elements occur in the restricted zone where the fall is 4m or more | Check fall height, restricted zone and applicable infill requirements | Replace with vertical or compliant infill design |
| Headroom below 2000mm | The clear vertical height above a stair nosing is less than 2000mm | Measure vertically from nosing to the underside of any obstruction above | Raise obstruction - may require structural modification |
| Non-graspable handrail profile | Handrail does not provide the graspable handhold required for the application | Attempt to grasp the handrail - if it cannot be gripped it is non-compliant | Provide a graspable profile complying with the applicable design requirements |
| Handrail not continuous | Handrail has gaps or does not extend from bottom to top of the flight | Walk the full flight with hand on rail - any gap is non-compliant | Install continuous handrail along full length of flight |
Stair compliance checklist
Measure every rise in the staircase - confirm rises are between 115mm and 190mm and variation meets the 5mm adjacent and 10mm whole-flight limits
Measure every going - confirm goings are between 240mm and 355mm and variation meets the applicable 5mm adjacent and 10mm whole-flight limits
Confirm twice the rise plus the going (2R + G) is between 550mm and 700mm for every step
Measure balustrade height at the landing - confirm minimum 1000mm from floor level
Measure balustrade height above every tread nosing - confirm minimum 865mm measured vertically from nosing to top of handrail
Check every opening in the balustrade - confirm openings prevent a 125mm sphere passing through where that test applies; check stair-opening exceptions
Check climbability restrictions in the 150–760mm zone where the protected fall is 4m or more
Confirm handrail is continuous from bottom to top of every flight with no gaps
Measure handrail height - confirm at least 865mm above stair nosings for the relevant housing stair
Attempt to grasp the handrail - confirm a graspable handhold meeting the applicable provisions
Measure headroom along the full stair width - confirm minimum 2000mm above every nosing
Test staircase structure - walk every tread and confirm no movement, bounce or deflection
Red flags
Building certifier did not conduct an inspection of the staircase installation before it was completed - stair compliance is a building permit condition
Balustrade height below 865mm above tread nosings - the most common stair compliance failure
Spindle spacing exceeds 125mm - a child safety non-compliance
Climb-facilitating elements in the restricted zone where the fall is 4m or more
Rise variation exceeding applicable limits - requires assessment and rectification
Handrail lacking a graspable handhold required for its application
Staircase movement under foot traffic - structural defect requiring engineering assessment
Builder attributes non-compliance to design intent rather than acknowledging it as a code violation
BUILTLY and lasting project records
BUILTLY is building a record of completed Australian homes that credits the builder, designers and trades behind each one.
BUILTLY is building a record of completed Australian homes that credits the builder, designers and trades behind each one.
Frequently Asked Questions
What are the NCC requirements for residential staircases in Australia?
For a standard house, the NCC sets rise limits of 115–190mm, going limits of 240–355mm and a minimum headroom of 2000mm. It also sets a rise-and-going formula, barrier and handrail requirements. See the table and the specific FAQs below for those checks; your certifier will confirm the rules for your stair category.
How high does a balustrade need to be in Australia?
A residential balustrade must be at least 1000mm high measured from the floor level at the top of the staircase and at any floor level 1000mm or more above the ground or the floor below. Along the rake of the staircase - measured from each tread nosing - the balustrade must be at least 865mm high. Both measurements must be met simultaneously. The most common compliance failure is a balustrade that meets the 1000mm requirement at the landing but drops below 865mm above tread nosings when measured along the rake.
What is the maximum spindle spacing for a staircase balustrade in Australia?
For relevant housing barriers, openings must prevent a 125mm sphere from passing through. Stairway geometry has specific exceptions, including the triangular opening at a tread, riser and bottom rail. Have the certifier check the applicable opening criteria rather than applying one spindle-spacing figure to every opening.
Can a staircase balustrade have horizontal rails in Australia?
For relevant housing barriers protecting a fall of 4m or more, elements between 150mm and 760mm above the floor must not facilitate climbing. Horizontal rails are not universally prohibited on lower barriers. Wire barriers also have specific tension, spacing and deflection requirements. Confirm the design with the certifier.
What should I check on a staircase at pre-handover inspection?
Measure every rise and going using the NCC table above. Adjacent rises and goings may vary by no more than 5mm and the maximum-to-minimum difference within a flight by no more than 10mm, under the NCC conditions. Check the formula, barriers, handrails and headroom against the same table and ask the certifier to check landings, slip resistance, open risers and winders.
Before handover, review the common stair design mistakes to focus your staircase checks.