Advice

What Does a Tiler Do in a Residential Construction Project in Australia

Last updated: October 2026

Tiling is one of the most visible trades in residential construction - and one of the most technically demanding when done correctly. A tiler installs ceramic, porcelain, natural stone and other tile finishes to floors and walls in wet areas, living areas and external spaces - but their work is only as good as the substrate beneath it and the waterproofing behind it. A tiler who tiles over inadequate waterproofing, an uneven substrate or without the correct adhesive and grout systems is setting up a failure that will manifest in cracked tiles, debonded tiles, failed grout and water damage - typically within two to five years. Understanding what a tiler does, what they depend on from preceding trades and what quality tiling looks like in a completed project is practical knowledge for any homeowner building in Australia.

What does a tiler do?

A tiler in residential construction installs tile finishes - ceramic, porcelain, natural stone, mosaic and other tile types - to floors, walls and other surfaces throughout the building. Their primary work locations in residential construction are wet areas - bathrooms, ensuites, laundries and shower enclosures - and external areas including alfresco floors, pool surrounds and feature walls.

The tiler's work follows the waterproofer's work - tiling cannot commence in any wet area until the waterproofing membrane has been inspected and certified by the building certifier. This sequencing is mandatory - not a preference - and the tiler should never commence tiling in a wet area without confirmation that the waterproofing inspection certificate has been issued.

The tiler's scope in a standard residential project includes preparation of the substrate - fixing and levelling any unevenness - selection and mixing of the correct adhesive system for the tile type and substrate, installation of tiles to the specified layout and pattern, grouting of all joints after the adhesive has cured and sealing of natural stone or grout where specified.

Tiling scope by area

AreaTypical tile applicationSubstrate preparation requiredKey sequencing requirement
Shower floorNon-slip porcelain or ceramic - typically 100mm to 200mm format with gradient to wasteWaterproofing inspected and certified - waste outlet at correct heightWaterproofing inspection certificate must be issued before tiling commences
Shower wallsCeramic or porcelain wall tile - format from 100x100mm to large format 600x1200mmWaterproofing applied and inspected - wall substrate checked for flatnessWaterproofing inspection certificate - adhesive selected for wet area application
Bathroom floor - wet zoneNon-slip ceramic or porcelain - must extend beyond shower screenWaterproofing to full wet zone - substrate level and flatWaterproofing inspection certificate - floor level confirmed before tiling
Bathroom walls - outside showerCeramic or porcelain wall tile - typically to full height or splashback heightPlasterboard or wet area sheeting confirmed - waterproofing to splash zonePlasterboard set and primed - wet area sheets confirmed
EnsuiteSame as bathroomSame as bathroomSame as bathroom
Laundry floor and wallsNon-slip ceramic - durable and easy to cleanWaterproofing to full floor - wall to 150mm minimumWaterproofing inspection certificate
Kitchen floorPorcelain or ceramic - format variesSubstrate level - expansion joints at perimeterJoinery installed before floor tiles in most layouts - confirm sequence with builder
Kitchen splashbackCeramic, porcelain, glass mosaic or natural stoneRender or plasterboard substrate - flat and primedAfter joinery installation - before fit-off
Alfresco floorExterior rated porcelain or natural stone - non-slipConcrete slab with correct fall - waterproofing if over habitable spaceConcrete cured - waterproofing inspected if over habitable space
Pool surroundExterior rated non-slip - frost resistant where applicableStructural engineer specification for pool shellSpecialist pool tiler - different adhesive and grout system

The waterproofing connection - why sequencing matters

The most critical quality dependency in tiling is the relationship between the waterproofer and the tiler. Tiling that commences before waterproofing is inspected - or tiling that proceeds without allowing the membrane to fully cure - creates a concealed defect that cannot be identified without removing the tiles.

Why the tiler must wait

The waterproofing inspection is a mandatory hold point. The building certifier must inspect and certify the waterproofing membrane before any tile is fixed. If tiling commences before the inspection - even if the membrane appears complete - the concealed membrane cannot be assessed without removing the tiles. If the membrane has a defect, the tiles must be removed, the defect rectified and the membrane re-inspected before tiling can recommence.

Curing time

After the waterproofing membrane is applied and the inspection certificate is issued, the membrane must be allowed to cure fully before tiles are fixed. Most liquid applied membrane systems require a minimum of 24 to 48 hours curing time - some require longer depending on temperature and humidity. Applying tile adhesive over a membrane that has not fully cured can damage the membrane and create adhesion problems.

The substrate flatness requirement

The tiler also depends on the substrate being adequately flat and level. AS 3958 - the Australian Standard for ceramic tile installation - specifies that substrate variation must not exceed 3mm under a 1800mm straight edge for most tile formats. Large format tiles - above 600mm in any dimension - require a flatter substrate - typically 2mm variation under 2000mm. A substrate that does not meet these tolerances requires the tiler to apply a levelling compound before tiling - an additional cost and time item that should be identified and resolved before tiling commences.

Tile adhesive and grout systems

The adhesive and grout system selected by the tiler must be appropriate for the tile type, the substrate type, the application environment and the expected movement conditions. Using the wrong adhesive or grout system is a common cause of tiling failures.

Adhesive selection

Cement-based tile adhesives - classified under AS ISO 13007 - are the standard for most residential tiling applications. The classification system rates adhesives by adhesion strength, slip resistance, open time and other properties. Wet areas require adhesives rated for wet area use. Large format tiles require adhesives with extended open time and anti-slip properties to prevent tiles from sliding before the adhesive sets. Natural stone tiles require adhesives that will not stain the stone through the back face.

Grout selection

Grout fills the joints between tiles and provides both a finished appearance and a waterproof seal at the joint surface. Cement-based grout - the most common - is available in sanded and unsanded formulations. Sanded grout is used for joints above 3mm width. Unsanded grout is used for joints below 3mm. Epoxy grout - more expensive but highly stain and chemical resistant - is used in commercial kitchens and other high-demand applications.

Movement joints

Every tiled surface must have movement joints - gaps in the tile installation filled with a flexible sealant rather than grout - to accommodate thermal and structural movement without cracking the tiles or debonding the adhesive. Movement joints are required at all changes of plane - floor-to-wall junctions - at perimeters - where the tiled surface meets walls or fixed structures - and at maximum 4.5 metre intervals in floor tiling. A tiler who fills movement joint locations with grout is setting up a failure - grout cracks under movement, tiles debond and the installation fails.

Common tiling defects

Understanding what common tiling defects look like - and what causes them - helps homeowners identify quality issues at the pre-handover inspection before accepting the work. The following table describes the most common tiling defects in residential construction.

DefectWhat it looks likeCauseRectification
Hollow or debonded tilesTile produces a hollow sound when tapped - may crack or liftInsufficient adhesive coverage - adhesive applied with incorrect notch trowel - adhesive skinned before tile placedRemove and relay affected tiles - identify and address adhesive coverage issue
Lippage - uneven tile edgesAdjacent tiles have a visible height difference - edge of one tile higher than adjacentUneven substrate - large format tiles on inadequate substrate - adhesive applied unevenlyMinor lippage - acceptable tolerance - excessive lippage requires tile removal and substrate preparation
Cracked tilesSingle or multiple tiles cracked - crack does not follow grout jointHollow under tile - structural movement - impact damageRemove cracked tiles - assess cause - relay or replace
Cracked groutGrout cracks along joints - particularly at perimeters and floor-to-wall junctionsMovement joint filled with grout rather than flexible sealant - insufficient movement jointsRemove grout at movement joint locations - install flexible sealant - regrout where required
Grout discolourationGrout colour varies across the installation - patchy or unevenInconsistent mixing - variable water addition - grouting before adhesive fully curedDeep clean - if persistent regrout affected areas
Stained natural stoneAdhesive stain visible through the face of natural stone tilesWrong adhesive used - cement adhesive staining light stoneRemove and relay with appropriate non-staining adhesive - may require professional stone cleaning
Missing grout - voidsGrout has not filled the full depth of the joint - voids visibleInsufficient grout - grout not fully worked into the jointRegrout affected joints
Incorrect fall - shower floorShower floor does not drain to waste - water poolsFloor not set to correct fall before tiling - waste outlet at wrong heightExpensive rectification - requires tile removal and relaying to correct falls

Tiling quality inspection checklist

Red flags

Tiling commences in wet areas before the waterproofing inspection certificate has been issued - the most serious tiling red flag
Tiler commences tiling on the same day the final membrane coat is applied - membrane has not cured
Substrate flatness has not been checked before tiling - large format tiles on an uneven substrate will have excessive lippage
Movement joints are absent - or movement joint locations are filled with grout rather than flexible sealant
Tiled shower floor does not drain freely to waste - incorrect fall set during tiling
Natural stone tiles are installed with a cement adhesive that can stain through the stone face
Hollow tiles identified during tapping inspection - insufficient adhesive coverage throughout
Grout is applied before adhesive has fully cured - premature grouting can pull tiles out of position and affect adhesive performance

BUILTLY and lasting project records

Tiling quality is one of the most visible indicators of construction standard in any completed home - and one of the elements that prospective buyers assess most directly during inspections. Consistent grout joints, correct falls, no lippage and properly executed movement joints are immediately apparent to an informed observer.

BUILTLY is building a record of completed Australian homes that credits the builder, designers and trades behind each one.

Frequently Asked Questions

What does a tiler do in a residential construction project in Australia?

A tiler installs tile finishes - ceramic, porcelain, natural stone and other tile types - to floors and walls in wet areas, living areas and external spaces throughout the building. In residential construction their primary work is in bathrooms, ensuites, laundries, kitchens and alfresco areas. Their work follows the waterproofer's work - tiling in wet areas cannot commence until the waterproofing inspection certificate has been issued by the building certifier. The tiler prepares the substrate, selects the correct adhesive system, installs tiles to the specified layout, grouts all joints after the adhesive cures and installs flexible sealant at movement joints and perimeters.

Why must waterproofing be inspected before tiling starts?

The waterproofing inspection is a mandatory hold point - the building certifier must inspect and certify that waterproofing has been correctly applied before any tile is fixed. If tiling commences before the inspection, the concealed membrane cannot be assessed without removing the tiles. If the membrane has a defect, the tiles must be removed, the defect rectified and the membrane re-inspected. Waterproofing failure is the single most common cause of serious post-construction defect claims in Australian residential buildings - the pre-tiling inspection is the primary protection against concealed defects that would otherwise only be discovered through water damage.

What are movement joints in tiling and why are they important?

Movement joints are gaps in the tile installation - at perimeters, at changes of plane and at maximum 4.5 metre intervals in floor areas - that are filled with flexible sealant rather than grout. They accommodate thermal and structural movement in the building without cracking the tiles or debonding the adhesive. A tiled surface without movement joints - or where movement joint locations have been grouted over - will crack as the building moves through seasonal temperature and humidity cycles. Grout cracks under movement - flexible sealant accommodates it. Movement joints filled with flexible sealant are one of the most reliable indicators of quality tiling workmanship.

What is tile lippage and is it a defect?

Lippage is the height difference between the edges of adjacent tiles - where one tile is higher than the adjacent tile at their shared joint. Some lippage is inherent in all tiled installations - AS 3958 permits a maximum of 1mm for rectified tiles and up to 2mm for unrectified tiles with joints above 6mm. Lippage above the permitted tolerance is a defect - it creates a trip hazard on floor tiles and a visible quality issue on wall tiles. Large format tiles - above 600mm in any dimension - are more susceptible to lippage because any substrate unevenness is amplified over the larger tile format. Substrate preparation before tiling is the primary control for lippage.

What should I check about tiling at the pre-handover inspection?

Tap every tile in wet areas - a hollow sound indicates debonding or insufficient adhesive coverage. Run your hand across tile joints in floor areas to check lippage - excessive height differences between adjacent tiles are a defect. Check all grout for cracking - particularly at floor-to-wall junctions and perimeters where movement is greatest. Confirm movement joints are present at perimeters and filled with flexible sealant not grout. Check the shower floor fall - pour water on the floor and confirm it drains freely to the waste with no pooling. Check grout joints for voids - joints should be fully filled with consistent colour throughout.

Related.