A licensed plumber's involvement in a residential construction project spans the full construction timeline - from the underground drainage installed before the slab is poured through to the hot water system commissioned at handover. Most homeowners associate plumbing with taps, toilets and pipes - the visible fixtures fitted off at the end of the project. In reality the plumber's most critical and most consequential work happens early - when underground drainage is permanently buried beneath the slab, when roof plumbing determines how the building drains and when waterproofing is applied to wet areas before tiling conceals it forever. Understanding what the plumber does at each stage and what to check before each stage proceeds is practical knowledge for any homeowner building in Australia.
Key takeaways
- A plumber's work spans the full construction timeline - from underground drainage before the slab to fixture fit-off at handover.
- Underground drainage is the most consequential stage - errors are permanently buried beneath the slab and cannot be corrected without cutting into it.
- Waterproofing is a mandatory inspection hold point - no tiling can commence without the waterproofing inspection certificate.
- A plumbing compliance certificate must be issued on completion of all plumbing work and provided to the homeowner at handover.
- Waterproofing failure is the single most common cause of post-construction defect claims in Australian residential buildings.
What is a licensed plumber?
A licensed plumber in Australia is a tradesperson who holds a current plumbing licence - issued by the state plumbing regulator - that authorises them to perform regulated plumbing work. On larger or more complex residential projects the plumbing system is designed by a hydraulic engineer rather than the installing plumber - see engaging a hydraulic engineer. Regulated plumbing work includes all work that connects to or modifies the water supply system, the drainage and sewerage system, the stormwater drainage system or in some states the gas supply system.
Plumbing in residential construction involves multiple subphases - underground drainage before the slab, above-ground rough-in during the frame stage, waterproofing in wet areas and fit-off of all fixtures and fittings at the end of construction. These phases may be performed by the same plumber or by different plumbers - the lead plumber who does the rough-in may not be the same person who does the fit-off.
All regulated plumbing work requires a compliance certificate - issued by the licensed plumber on completion. See the companion guide Plumbing Compliance Certificates Australia for the complete framework.
Plumbing scope by construction stage
| Construction stage | Plumbing work performed | What is installed | Compliance requirement |
|---|---|---|---|
| Pre-slab - underground drainage | Drainage rough-in before concrete is poured | Sewer connection, underground drainage pipes, waste outlet positions for all wet areas, stormwater drainage connection | Plumbing permit required before work commences in Queensland |
| Slab stage | Slab penetrations | Sleeves and penetrations through the slab for above-ground plumbing - waste pipes through slab | Included in pre-slab compliance |
| Frame stage - above-ground rough-in | Water supply rough-in and above-ground drainage | Cold and hot water supply pipes to all fixtures, above-ground drainage connections, hot water unit rough-in, gas pipework where applicable | No compliance certificate at this stage - covered in final certificate |
| Lock-up stage | Roof plumbing | Gutters, downpipes, valleys, flashings - weatherproofing the roof drainage | No separate compliance - included in final |
| Fixing stage - waterproofing | Wet area waterproofing | Waterproofing membrane applied to all wet area floors and walls | Mandatory inspection by building certifier before tiling - waterproofing inspection certificate |
| Fixing stage - tiling | Tiling over waterproofed surfaces | Not plumbing work - but plumber coordinates waste outlet positions with tiler | No plumbing compliance at this stage |
| Fit-off stage | Fixture and fitting installation | Tapware, basins, toilets, showers, baths, laundry trough, hot water system connection, dishwasher connection | Final plumbing compliance certificate issued at completion of fit-off |
| Commissioning | System testing and commissioning | Pressure testing of water supply, drainage flow testing, hot water temperature confirmation | Compliance certificate confirms all testing passed |
Underground drainage - the most consequential plumbing stage
The underground drainage stage - installing the sewer connection, drainage pipes and wet area waste outlet positions before the slab is poured - is the most consequential plumbing stage in any residential construction project. Errors made at this stage are permanently buried beneath the slab.
Waste outlet positions
Every wet area fixture - toilet, shower, bath, basin, laundry trough, kitchen sink - has a waste outlet that must be positioned precisely during the underground drainage stage. A toilet waste outlet that is 20mm from the correct position will cause the toilet pan to sit incorrectly - either not covering the waste outlet or rocking on the floor surface. A shower waste that is positioned at the wrong height relative to the finished floor level will drain inadequately or create a trip hazard at the shower entry.
These positions cannot be changed after the slab is poured without cutting into the slab - an expensive and disruptive rectification. Confirming waste outlet positions against the architectural plan and the plumbing plan before concrete is poured is one of the most practically important pre-pour checks.
Drainage grades
All drainage pipes must be installed at a minimum fall - gradient - that ensures waste flows freely to the sewer. The minimum fall for most residential drainage is 1 in 40 - 25mm fall per metre of pipe. Drainage installed at insufficient fall will drain slowly, allow solids to settle and create recurring blockages. This grade must be set correctly during installation - it cannot be adjusted after the slab is poured.
The waterproofing stage - critical hold point
Waterproofing in wet areas is the plumbing work with the highest consequences if done incorrectly - and the most important mandatory inspection hold point in the fixing stage.
What waterproofing involves
The waterproofer applies a liquid membrane system to all wet area floor and wall surfaces - bathrooms, ensuites, laundry - before tiles are installed. The membrane must be applied to the floor surface, the bottom 150mm of all wall surfaces and the full height of shower walls to at least 1800mm. All floor-to-wall junctions and wall-to-wall junctions must receive additional membrane coverage with fibre reinforcement embedded.
The mandatory inspection
Before any tiling commences, the waterproofing membrane must be inspected by the building certifier - who confirms the membrane has been correctly applied to the required surfaces and meets the requirements of AS 3740. This inspection is a mandatory hold point - no tiling can commence without the inspection certificate being issued.
Why it matters
Waterproofing failure is the single most common cause of post-construction defect claims in Australian residential buildings. Water penetrating through a failed membrane causes damage to the building fabric beneath and adjacent to the wet area - damage that is invisible until it is extensive and expensive. The waterproofing inspection certificate is one of the most important documents in any completed home's record.
Plumbing compliance requirements
| Work type | Compliance certificate required | When issued | State variations |
|---|---|---|---|
| Underground drainage and sewer connection | Yes - plumbing compliance certificate | After all plumbing work is complete - at fit-off stage | In Queensland Form 4 required - inspection by certifier before certificate |
| Water supply rough-in | Included in final compliance certificate | At completion of all plumbing work | No separate certificate for rough-in stage |
| Waterproofing | Waterproofing inspection certificate - separate from plumbing compliance | Before tiling commences - mandatory hold point | Required in all states |
| Gas installation | Separate gas compliance certificate | After all gas work is complete | Gas licence separate from plumbing licence in most states |
| Hot water system - full installation | Included in plumbing compliance certificate | At fit-off completion | May require separate electrical compliance for electric hot water |
| Roof plumbing - gutters and downpipes | Included in plumbing compliance certificate | At fit-off completion | Part of the licensed plumber's scope |
What to check at each plumbing stage
Pre-slab - confirm waste outlet positions against the plumbing plan and architectural plan before concrete is poured - position errors cannot be corrected after the pour
Pre-slab - confirm drainage pipes are installed at correct grade - minimum 1 in 40 fall - before concrete is poured
Pre-slab - in Queensland confirm a plumbing and drainage permit has been obtained before underground work commenced
Frame stage - confirm hot and cold water supply pipes have been pulled to all specified fixture locations
Frame stage - confirm gas pipework has been roughed in to all specified gas appliance locations
Waterproofing - do not allow tiling to commence before the waterproofing inspection certificate is issued - inspect the certificate personally before approving tiling
Fit-off - turn on all taps and check hot and cold water at every fixture
Fit-off - run every shower for five minutes and check for leaks at floor waste and wall junctions
Fit-off - check under every vanity and kitchen sink for moisture or water staining at connections
Fit-off - confirm hot water temperature at bathroom fixtures - approximately 50°C - tempering valve correctly set
At handover - confirm plumbing compliance certificate has been issued and received
Red flags
Plumber cannot confirm their current licence number before commencing work
Underground drainage is installed without a plumbing permit in Queensland
Concrete is poured before waste outlet positions have been confirmed against the architectural plan
Tiling commences before the waterproofing inspection certificate is issued
Hot water system is installed without a licensed electrician performing the electrical connection - requires separate electrical compliance certificate
Plumber cannot confirm who will be conducting the fit-off - different plumber from rough-in without handover documentation
Plumbing compliance certificate is not provided at handover - or builder suggests it will follow later
BUILTLY and lasting project records
BUILTLY is building a record of completed Australian homes that credits the builder and specialist trades behind each one.
BUILTLY is building a record of completed Australian homes that credits the builder and specialist trades behind each one.
Frequently Asked Questions
What does a plumber do in a residential construction project in Australia?
A licensed plumber's work in residential construction spans the full build programme. Before the slab is poured, the plumber installs underground drainage - the sewer connection, drainage pipes and waste outlet positions for all wet areas. During the frame stage, the plumber installs water supply pipes and above-ground drainage. During the fixing stage, the plumber or waterproofer applies waterproofing to all wet areas - which must be inspected before tiling. At fit-off, the plumber installs all fixtures - tapware, basins, toilets, showers, hot water system. A plumbing compliance certificate is issued on completion of all work.
What is the most important plumbing stage in a new home build?
The underground drainage stage - before the slab is poured - is the most consequential because errors at this stage are permanently buried and cannot be corrected without cutting into the slab. Waste outlet positions that are even slightly wrong will cause fixture alignment problems that are expensive to rectify. Drainage pipes installed at insufficient fall will cause recurring drainage problems throughout the life of the building. Confirm waste outlet positions against the architectural plan before allowing concrete to be poured - this is one of the most practically important pre-pour checks.
What is the waterproofing inspection and why is it mandatory?
The waterproofing inspection is a mandatory hold point in every Australian state - the building certifier must inspect and certify that waterproofing has been correctly applied to all wet area surfaces before any tiling can commence. Once tiles are laid over the waterproofing, the membrane cannot be inspected without removing the tiles. Waterproofing failure is the single most common cause of post-construction defect claims - water penetrating through a failed membrane causes damage to the building fabric that is invisible until it is extensive and expensive. Do not allow tiling to commence without the waterproofing inspection certificate being issued.
What documents should I receive from the plumber at handover?
At handover you should receive the plumbing compliance certificate - confirming all plumbing and drainage work is compliant and certified by the licensed plumber. You should also receive the waterproofing inspection certificate - confirming waterproofing was inspected before tiling. In Queensland the Form 4 Certificate of Compliance must be lodged with council and a copy provided to the homeowner. If gas work was performed, a separate gas compliance certificate should be provided. If the hot water system has an electrical connection, a separate electrical compliance certificate for that connection should also be provided.
What is the difference between a plumber's rough-in and fit-off?
The rough-in is the first phase of plumbing work - installing all underground drainage, water supply pipes and above-ground drainage before walls and floors are finished. The rough-in is hidden within the building fabric and must be completed correctly before surfaces are closed. The fit-off is the second phase - installing all visible fixtures and fittings after the internal linings, tiling and finishing are complete. Fit-off includes tapware, basins, toilets, showers, the hot water system connection and the dishwasher connection. The rough-in and fit-off may be performed by the same licensed plumber or by different plumbers under the same licence.