Air Conditioning for New Homes Australia: What to Know Before You Build

Last updated: October 2026

Air conditioning is no longer optional in most Australian homes - it is a fundamental part of the build specification. But the decisions you make before construction starts have a significant impact on what your system costs, how well it performs and whether your new home can take advantage of solar power and smart home technology. This guide covers everything you need to decide and document before your slab goes down.

Why Air Conditioning Decisions Need to Happen Before You Build

Getting air conditioning right in a new home is far easier and cheaper at the design stage than after construction. Once your ceiling cavities are closed, your electrical switchboard is set and your roof trusses are in place, retrofitting a ducted system becomes a significantly more expensive and disruptive exercise.

Installing ducted air conditioning during construction typically costs $3,000 to $5,000 less than the equivalent retrofit after handover. Conduit runs, duct pathways, outdoor unit locations and electrical capacity all need to be planned into the design - not bolted on later.

There are also NatHERS Whole of Home rating implications. Under the National Construction Code 2022, all new homes in Australia must meet a minimum 7-star thermal performance rating and a Whole of Home rating of at least 60 out of 100. The air conditioning system you specify can affect this rating - efficient reverse cycle systems using less energy per unit of output contribute positively to the Whole of Home score.

Air Conditioning System Types for New Homes

Ducted Reverse Cycle Air Conditioning

Ducted reverse cycle is the most popular whole-home climate solution for new Australian homes. A single outdoor unit connects to a hidden network of ducts in the ceiling cavity, distributing conditioned air through vents in every room. The system provides both heating and cooling from a single installation and can be divided into zones - typically two to eight zones depending on home size - allowing different areas to be controlled independently.

During new construction, the ducted system is installed before the ceiling is closed, meaning ductwork is concealed and the finished result is clean with only small vents visible in each room.

Cost range (supply and installation during construction):

  • 3-bedroom single-storey home: $6,000 to $10,000
  • 4-bedroom home: $9,000 to $14,000
  • 5+ bedroom or double-storey home: $12,000 to $20,000+

Running costs: approximately $0.50 to $1.50 per hour depending on system size, efficiency rating and zoning.

Pros

  • Whole-home comfort from a single system
  • Clean concealed aesthetic
  • Excellent zoning capability
  • Adds significant property value
  • Compatible with smart home and solar systems

Cons

  • Higher upfront cost
  • Requires adequate roof cavity space
  • Minimum project sizes with some contractors
  • Running costs higher without good zoning discipline

Indicative cost: Ducted reverse cycle - $6,000 to $20,000+ installed during construction depending on home size

Split System Air Conditioning

A split system consists of one outdoor unit connected to one indoor wall-mounted unit, cooling or heating a single room or open-plan zone. Multiple split systems can be installed throughout a home - one per bedroom and one per living area - to provide whole-home coverage at a lower upfront cost than ducted.

Split systems are the most common choice for apartments and smaller homes. For larger homes, the combined cost of multiple units plus installation often approaches the cost of a ducted system while delivering less comfort consistency and a less clean aesthetic.

Cost range (supply and installation per unit):

  • Small 2.5 kW unit (bedroom): $1,500 to $2,500
  • Medium 5 kW unit (living room): $1,800 to $3,500
  • Large 7 kW unit (open plan): $2,200 to $4,500

A typical 4-bedroom home with five split systems installed during construction would cost approximately $8,000 to $16,000 total.

Indicative cost: Split system - $1,500 to $4,500 per unit installed | Typical 4-bedroom home: $8,000 to $16,000

Multi-Head Split System

A multi-head or multi-split system connects multiple indoor units to a single outdoor unit. This is a cost-effective middle ground between individual split systems and full ducted - the outdoor unit footprint is smaller than ducted, but coverage is broader than a single split.

Indicative cost: Multi-head split system - $4,200 to $8,000 installed

Evaporative Cooling

Evaporative cooling works by drawing warm outside air through wet filter pads, lowering the temperature through evaporation. It is highly energy-efficient and cheap to run, but only effective in dry climates. Evaporative cooling is common in Melbourne, Adelaide and Perth but is not suited to the humidity of Brisbane, Sydney coastal areas, Darwin or Queensland generally.

Indicative cost: Ducted evaporative cooling - $3,500 to $7,500 installed | Only suitable for dry climates

System Type Comparison

System typeCost installedBest forNot suited to
Ducted reverse cycle$6,000 - $20,000+Whole-home comfort, larger homesSmall homes, apartments
Split system (per unit)$1,500 - $4,500Apartments, smaller homes, targeted roomsLarge homes needing whole-home coverage
Multi-head split$4,200 - $8,000Mid-size homes, 2-4 zonesLarge or complex layouts
Evaporative cooling$3,500 - $7,500Dry climates: Melbourne, Adelaide, PerthHumid climates: Brisbane, Sydney, Darwin

Ducted vs Split System - Which Is Right for Your New Home?

The decision comes down to home size, climate, budget and lifestyle. Use this as a starting point:

Choose ducted if:

  • Your home is 3 bedrooms or larger
  • You want whole-home comfort from a single system
  • A clean, concealed aesthetic matters to you
  • You plan to stay in the home long-term
  • You want the best compatibility with smart home systems and zoning

Choose split systems if:

  • Your home is a smaller apartment or 2-bedroom dwelling
  • You only need cooling or heating in specific rooms
  • You want the lowest upfront cost
  • You are comfortable with wall-mounted indoor units visible in each room

For most new 4-bedroom Australian family homes, ducted reverse cycle installed during construction is the most cost-effective and practical long-term solution. Once you have settled on a system type, the BUILTLY guide to air conditioning installation cost in Australia sets out ducted and split system pricing by house size, capacity and zones, and what to check before hiring an installer.

What to Specify Before Construction Commences

  • Confirm with your builder whether air conditioning is included in the base contract price or is a provisional sum, prime cost item or add-on
  • Decide between ducted, split or multi-head before the design is finalised - duct routes and ceiling cavity requirements affect truss design
  • Identify and lock in the outdoor unit location on the plans - placement affects noise, aesthetics and access for future servicing
  • Confirm the electrical load for your chosen system is included in the switchboard specification - ducted systems require a dedicated circuit
  • Confirm whether conduit runs for future split systems are included during construction if you are not installing ducted now
  • Ask your builder to include pre-wiring or conduit routing for any rooms where split systems will be added post-handover
  • If installing solar panels, confirm the system is solar-compatible and that a smart controller or solar diverter can be integrated
  • Confirm zoning design with your air conditioning contractor before ductwork is installed - it is very difficult to change zones after the ceiling is closed
  • Ensure the air conditioning specification is documented in the building contract - not just a verbal agreement

For a complete framework on what should be included in your building contract, refer to the BUILTLY guide. If air conditioning is listed as a provisional sum or prime cost item, understand the difference and what to check before signing.

What Is Included in a Builder's Contract vs What Is an Add-On

This is one of the most common sources of cost shock in new home builds. Understanding what is standard and what is extra before you sign will save thousands.

What Builders Typically Include as Standard

Many volume builders include a basic split system or basic ducted allowance as a standard inclusion - but the specification matters. A standard inclusion might cover a single split system in the main living area only, or a ducted system with a limited number of outlets and no zoning.

Always check:

  • How many outlets or indoor units are included
  • Whether zoning is included or an upgrade
  • What brand and capacity is specified
  • Whether the outdoor unit location has been planned into the design

What Is Commonly a Provisional Sum or Prime Cost Item

Air conditioning is frequently listed in building contracts as either:

  • A prime cost (PC) item - meaning a dollar allowance is included in the contract but the actual product has not been selected yet. If your chosen system exceeds the PC allowance, you pay the difference.
  • A provisional sum (PS) item - meaning an estimated allowance for both supply and labour where the final scope is not fully defined. Provisional sums can vary significantly from the final cost.

Both require careful scrutiny. Ask your builder to itemise the full specification - brand, model, capacity, number of zones and number of outlets - before signing. For more on managing these allowances refer to the BUILTLY guides on provisional sums and prime cost items.

Common Air Conditioning Add-Ons to Budget For

  • Additional zones: typically $500 to $1,500 per zone above the standard inclusion
  • Additional outlets: typically $300 to $800 per outlet
  • Wi-Fi or smart home controller upgrade: $300 to $800
  • Switchboard upgrade to accommodate the electrical load: $1,000 to $2,000
  • Outdoor unit screen or enclosure: $500 to $2,000

Air Conditioning and NatHERS - What You Need to Know

Under the National Construction Code 2022, all new homes in Australia must achieve a minimum 7-star NatHERS thermal performance rating and a Whole of Home energy use rating of at least 60 out of 100. The Whole of Home rating captures the energy use of fixed appliances including heating and cooling systems, hot water, lighting and pool or spa equipment. Solar panels can offset energy use and improve the Whole of Home score.

The air conditioning system you choose affects your Whole of Home rating. Efficient reverse cycle systems - particularly those with high energy star ratings and inverter technology - contribute positively. Air-source heat pumps and reverse cycle air conditioners typically deliver three to five times more heating or cooling energy than the electricity they consume, making them the most efficient choice for new homes.

Key points for new builds:

  • Your NatHERS assessor should be engaged at the design stage, not after plans are locked
  • The air conditioning type and brand do not need to be finalised for the NatHERS star rating assessment, but the system must be specified for the Whole of Home rating
  • Choosing an efficient reverse cycle system over a less efficient option can meaningfully improve your Whole of Home score
  • A higher Whole of Home score means lower running costs and better energy performance over the life of the home

Air Conditioning and Solar Power Compatibility

A new home with solar panels and an efficient reverse cycle air conditioning system is one of the most cost-effective combinations available to Australian homeowners. Running the air conditioning during peak solar generation hours - typically 10am to 3pm - allows you to cool or pre-cool your home using power that is either free or exported at a low feed-in tariff rate.

For maximum solar compatibility:

  • Choose an air conditioning system with a Wi-Fi or smart controller that allows scheduled or automated operation
  • A solar diverter or smart home energy management system can automatically run the air conditioner when solar generation is at its peak
  • Inverter technology in reverse cycle systems adjusts compressor speed to match the load, using less power when the home is already close to the target temperature - this works particularly well with variable solar output
  • Confirm with your solar installer and air conditioning contractor that the system supports integration before installation

Running costs for ducted reverse cycle can be reduced by 40 to 60 percent in homes with appropriately sized solar panel systems when scheduling is used effectively. For more on energy-efficient building refer to the BUILTLY guide on sustainable home building.

Smart Home Integration for Air Conditioning

New home construction is the ideal time to integrate air conditioning into a broader smart home system. Retrofitting smart controls after handover is possible but more complicated and expensive.

Leading brands including Daikin, Mitsubishi Electric, Panasonic, Fujitsu and LG all offer Wi-Fi enabled systems that connect to dedicated apps and can be integrated with platforms including Google Home, Amazon Alexa and Apple HomeKit.

For smart home readiness, confirm during the build:

  • Wi-Fi enabled controller is included or specified as an upgrade
  • Smart home hub or conduit for data cabling is planned in the same stage as air conditioning installation
  • If using a whole-home automation system, confirm compatibility between the air conditioning brand and the automation platform before specifying

Air Conditioning Brands Commonly Used in Australian New Homes

Daikin

Japanese brand widely regarded as the market leader in Australia for ducted systems. Known for reliability, efficiency and a strong local service network. Premium price point.

Mitsubishi Electric

Premium brand with a strong reputation for quiet operation and energy efficiency. Popular for both ducted and split systems.

Panasonic

Strong mid-to-premium option with reliable inverter technology and good energy ratings. Well regarded in Queensland and NSW markets.

Fujitsu

Popular mid-range choice with a solid range of residential ducted and split systems. Competitive pricing.

LG

Strong in the split system market with good Wi-Fi integration. Wi-Fi Ready models popular in new builds.

Rinnai and Brivis

Common in southern states for ducted systems, particularly in Victoria where reverse cycle heating performance in colder winters is important.

Brand choice should be made in consultation with a local licensed installer who can advise on service availability and parts support in your area.

Questions to Ask Your Builder About Air Conditioning

  • Is air conditioning included in the base contract price or is it a provisional sum or prime cost item?
  • What brand, model and capacity is specified?
  • How many zones and how many outlets are included?
  • Where is the outdoor unit located on the plans?
  • Is the electrical switchboard specified to handle the air conditioning load?
  • Is conduit or pre-wiring included for any rooms where split systems will be added later?
  • Is a Wi-Fi or smart controller included or available as an upgrade?
  • What is the warranty on the system and who is responsible for warranty claims - the builder or the air conditioning contractor?
  • Has the system been specified in writing in the building contract?

For a comprehensive framework on managing communication with your builder throughout construction, refer to the BUILTLY guide on how to manage a builder during construction. When comparing quotes from multiple builders, refer to how to compare quotes from builders.

Air Conditioning Specifications and BUILTLY

BUILTLY is building a record of completed Australian homes that credits the builder, designers and trades behind each one.

Frequently asked questions

Should I install ducted or split system air conditioning in my new home?

For most new Australian homes of three bedrooms or larger, ducted reverse cycle installed during construction is the recommended option. It provides whole-home comfort from a single system, a cleaner aesthetic and better compatibility with smart home and solar systems. Split systems are more practical for smaller homes, apartments or where budget is the primary constraint.

How much does ducted air conditioning cost in a new build?

Installing ducted reverse cycle air conditioning during new construction typically costs $6,000 to $10,000 for a 3-bedroom home, $9,000 to $14,000 for a 4-bedroom home and $12,000 to $20,000 or more for a larger or double-storey home. Installing during construction is typically $3,000 to $5,000 cheaper than retrofitting after handover.

Does air conditioning affect my NatHERS rating?

The NatHERS star rating is based on the thermal performance of the building shell - orientation, insulation, glazing and construction materials - and is not directly affected by the air conditioning brand or type you choose. However, the Whole of Home rating required under NCC 2022 does capture the energy use of fixed appliances including heating and cooling. Choosing an efficient reverse cycle system with a high energy star rating contributes positively to your Whole of Home score.

Can I run my air conditioning on solar power?

Yes, and new homes with solar and reverse cycle air conditioning are one of the most effective combinations for reducing running costs. Scheduling the air conditioning to operate during peak solar generation hours - typically 10am to 3pm - allows you to run the system on solar energy. Inverter technology and smart Wi-Fi controllers make this easier to automate.

What should be included in the building contract for air conditioning?

The building contract should specify the brand, model and capacity of the system, the number of zones and outlets, the outdoor unit location, the electrical switchboard specification and any smart home or Wi-Fi controller inclusions. If air conditioning is listed as a provisional sum or prime cost item, request a detailed scope before signing so you understand the allowance and what any upgrades will cost.

Related guides