Australia has one of the highest rates of residential solar adoption in the world - and a new home build is the single best opportunity to get it right. Decisions made at the design stage about roof orientation, conduit runs, switchboard capacity and inverter location affect system performance for the next 25 years. Decisions left until after handover cost more, deliver less and are harder to undo. This guide covers everything you need to decide before construction starts - system sizing, costs, rebates, NatHERS implications, battery storage, roof design and what should be in the builder's contract.
Why Solar Decisions Need to Happen Before You Build
Installing solar during construction is cheaper, cleaner and more effective than retrofitting after handover. The key advantages of planning solar into the build from day one:
- Pre-wiring conduit runs before walls are closed costs a fraction of cutting into finished walls later
- Installing panels while scaffolding is already up for construction saves $500 to $2,000 in scaffold hire at a later date
- Roof orientation, pitch and truss design can be optimised for solar during the design phase at minimal or no cost
- Inverter and battery locations can be planned into the garage or utility space during construction
- Switchboard capacity can be specified correctly from the start - avoiding a $500 to $1,500 upgrade later
- In New South Wales, BASIX requirements make solar on new homes effectively mandatory
Engaging a CEC-accredited solar installer at the same time as your architect or builder - not after the roof is on - is the single most cost-effective decision you can make for your solar system.
How Much Do Solar Panels Cost in Australia in 2026?
Solar system costs in Australia are quoted on a per-kilowatt (kW) basis. As a rule of thumb, budget approximately $1,000 per kW installed for a quality system after the federal STC rebate. A 6.6kW system - the most common residential size - typically costs $5,000 to $8,000 fully installed after rebate in 2026.
| System size | Panels | Daily output | Cost after STC | Best suited to |
|---|---|---|---|---|
| 5kW | 12-14 | 18-22 kWh | $4,500 - $7,000 | Smaller homes, 1-2 people |
| 6.6kW | 16-18 | 24-28 kWh | $5,000 - $8,000 | Standard 3-4 bedroom home |
| 8kW | 19-22 | 28-34 kWh | $6,500 - $9,500 | Larger homes, EV charging |
| 10kW | 23-28 | 35-42 kWh | $8,000 - $10,500 | Large homes, high energy use |
| 13kW | 30-35 | 45-55 kWh | $10,000 - $14,000 | Very large homes, batteries, EVs |
Prices include the federal STC rebate applied at point of sale and GST. Daily output figures are indicative for a north-facing roof at typical Australian latitudes. Prices vary by state, installer and equipment tier. Premium panels and inverters add 20 to 40 percent to system cost.
๐ก Indicative cost: Standard 6.6kW solar system - $5,000 to $8,000 installed after STC rebate
The Federal STC Rebate - How It Works
The Small-scale Technology Certificates (STC) scheme is Australia's federal solar incentive. When you install a solar system, your installer calculates the number of STCs generated based on your system size and location - sunnier locations like Queensland generate more STCs than Tasmania. The installer typically applies the STC value as an upfront discount at point of sale, so the price you are quoted already reflects the rebate.
Key points for new builds in 2026:
- The STC rebate reduces in value on 1 January each year and ends completely on 31 December 2030
- A 6.6kW system in Queensland or NSW currently attracts an STC discount of approximately $1,500 to $2,000; a 10kW system approximately $2,000 to $3,000
- The rebate applies regardless of panel or inverter brand - it is based on system capacity and location only
- Only CEC-accredited installers using CEC-approved equipment are eligible to claim STCs
State Rebates and Additional Incentives
- Victoria - the Solar Homes Program offers rebates of up to $1,400 for eligible households with combined income under $210,000 and property value under $3 million
- New South Wales - BASIX requirements make solar effectively standard practice; no separate panel rebate but feed-in tariff structures apply
- South Australia - no dedicated panel rebate as at 2026 but strong feed-in tariff structures and very high solar adoption
- Queensland, WA, ACT, Tasmania, NT - check relevant state energy authority websites for current incentive availability
๐ก Indicative saving: Federal STC rebate saves approximately $1,500 to $3,000 at point of sale depending on system size and location
Roof Design for Solar - What to Get Right Before the Slab Goes Down
The roof design decisions made during the architectural phase have the largest long-term impact on solar system performance. Changes at design stage cost nothing. Changes after the frame is up cost thousands.
Orientation
In Australia, true north-facing roof planes produce the maximum annual solar generation. A north-facing roof at a pitch of 20 to 35 degrees is the benchmark for optimal performance. Acceptable variations with minimal output loss of 5 to 10 percent include north-east and north-west orientations.
East and west-facing roof planes are viable secondary options. A split array across east and west faces can flatten the generation profile across the day - useful if your household uses power in the morning and evening rather than at midday.
South-facing roofs generate significantly less power and are generally not recommended as the primary panel orientation.
Pitch
A roof pitch of 15 to 35 degrees provides near-optimal performance for most Australian locations. Flat roofs require tilt frames to achieve an appropriate angle - adding $500 to $2,000 to installation cost. Very steep roofs above 40 degrees increase wind loading on panels and can complicate installation.
Available Roof Area
A standard 6.6kW system of 16 to 18 panels requires approximately 27 to 32 square metres of unobstructed, north-facing roof space. Plan the location of roof penetrations - skylights, ventilation, chimneys, whirlybirds, air conditioning units and antennas - on the south or east face of the roof rather than the north face.
Shading
Shading is the single largest performance reducer for solar panels. Even partial shading of one panel in a string can significantly reduce the output of the entire string. During the design phase, consider:
- Neighbouring buildings and their shadow patterns at different times of year
- Planned trees and their mature height relative to the roof line
- Roof elements including chimneys, elevated parapets and raised ridge lines
Ask your solar installer to conduct a shading analysis using your plans before the roof is finalised.
Roof Structure and Load Capacity
Solar panels add approximately 12 to 15 kilograms per panel to the roof structure, plus wind uplift loading. For a standard 16 to 18 panel system this is approximately 200 to 270 kilograms of additional dead load. Most standard residential roof trusses accommodate this without modification, but confirm with your builder or structural engineer before the frame is designed.
What to Specify Before Construction Commences
What Should Be in the Builder's Contract
Solar is frequently a source of confusion in new home building contracts. Understanding what is the builder's responsibility and what is the homeowner's separate engagement avoids costly surprises.
What Builders Typically Include
Many volume builders offer solar as a standard inclusion or an upgrade package. The specification matters enormously. Always confirm in writing:
What Is Typically the Homeowner's Separate Scope
In architecturally designed homes and most custom builds, solar is typically engaged directly by the homeowner separately from the builder's contract. In this case, confirm with the builder that conduit runs will be completed before walls are closed, the switchboard connection point, meter configuration for solar feed-in, and scaffolding access if needed. See how to manage a builder during construction for coordination guidance.
The Builder's Solar Package Warning
Builder-supplied solar packages in volume new home builds are frequently the weakest component of an otherwise well-specified home. The solar system is often the item where builders apply the tightest margin - resulting in cheap panels, basic inverters and poor installation quality.
Engaging your own CEC-accredited solar installer independently of the builder and specifying the system yourself typically delivers a better system for a similar or lower cost. If the solar component in your contract is listed as a provisional sum or prime cost item, request a detailed scope before signing.
Solar Panels and NatHERS - The Whole of Home Connection
Under the National Construction Code 2022, all new homes must achieve a minimum 7-star NatHERS thermal performance rating and a Whole of Home energy use rating of at least 60 out of 100. Solar panels directly affect the Whole of Home rating.
The Whole of Home rating captures the annual energy use of fixed appliances including heating and cooling, hot water, lighting and pool or spa equipment - and offsets this with on-site renewable energy generation including rooftop solar.
Key NatHERS points for new builds:
- The NatHERS star rating is based on building shell performance and is not directly affected by solar
- The Whole of Home rating is where solar has its impact - it offsets appliance energy consumption
- A home targeting an 8 or 9-star NatHERS rating combined with solar and efficient appliances can achieve a Whole of Home score at or above 100
- Engage your NatHERS assessor at the design stage to model the combined effect
For homes pursuing exceptional thermal performance, see the BUILTLY guide on building a passive house in Australia and sustainable home building.
Battery Storage - Is It Worth It for a New Home?
Battery storage allows households to store excess solar generation during the day and use it at night, reducing grid electricity purchases during expensive peak periods.
Battery Costs in 2026
| Battery system | Usable capacity | Installed cost | Best suited to |
|---|---|---|---|
| Entry-level battery | 5-7 kWh | $6,000 - $9,000 | Smaller homes, supplement solar |
| Mid-range battery | 10-13.5 kWh | $9,000 - $14,000 | Standard family home |
| Premium battery | 13.5kWh+ | $14,000 - $20,000+ | Large homes, backup power, EVs |
| Whole-home backup | 20kWh+ | $20,000 - $40,000+ | Off-grid or blackout resilience |
Prices are indicative for 2026 including installation. A new federal battery rebate covering approximately 30 percent of battery cost is available for eligible CEC-approved systems.
Is Battery Storage Worth It in 2026?
For most Australian households, a typical 10kWh battery costs $9,000 to $14,000 installed and saves approximately $800 to $1,200 per year in electricity costs - implying a payback period of 7 to 12 years. Battery systems typically last 10 to 15 years. On pure financial return, the case is marginal for most households.
Battery storage makes stronger financial sense when:
- Your household has time-of-use tariffs with high peak rates above 45 cents per kWh
- You have or plan to install an electric vehicle
- You are in an area with frequent grid outages and value backup power
- The federal or state battery rebate applies to your installation
Battery-Readiness as the Minimum Specification
For most new home builds, the pragmatic approach is to install a hybrid inverter during construction - which adds approximately $500 to $1,500 to the inverter cost - and plan the battery location into the garage or utility space. This means a battery can be added later with minimal additional installation cost.
๐ก Indicative cost: Battery storage system - $6,000 to $20,000+ installed depending on capacity | Federal rebate of approximately 30% available for eligible systems
System Types - String Inverter, Hybrid Inverter or Microinverters
String Inverter
The most common and lowest-cost inverter type. All panels connect in a string to a single inverter. Performs well on unshaded, consistent roof planes. If one panel is shaded, the output of the entire string is reduced. Entry-level to mid-range cost.
Hybrid Inverter
A string inverter with built-in battery connection capability. Allows seamless battery addition at a later date without replacing the inverter. Recommended for all new home builds as the incremental cost is small and the future flexibility is significant.
Microinverters
Individual small inverters mounted on each panel. Each panel operates independently - shading or failure of one panel does not affect others. Best suited to complex roof designs, mixed orientations or sites with unavoidable partial shading. Higher upfront cost - typically $1,000 to $3,000 more for a standard residential system.
Which to Choose for a New Build
Clean north-facing roof, minimal shading
A hybrid string inverter is recommended - low cost, battery-ready and appropriate for the site conditions.
Complex roof, mixed orientations, shading
Microinverters or DC optimisers provide better performance and are worth the additional cost.
Solar Panel Brands and Quality Tiers
Budget tier
Jinko Solar, Trina Solar, Seraphim
Reliable, widely installed across Australia, good warranty terms. Panels typically cost $100 to $150 per panel. Recommended for homeowners prioritising fastest payback period.
Mid-range tier
Canadian Solar, Longi Solar, Q Cells
Step up in efficiency and warranty terms. Good balance of cost and performance for most residential applications.
Premium tier
REC, SunPower/Maxeon, Panasonic
Higher efficiency, longer product warranties (25 years on the product itself), lower degradation over time. Panels typically cost $250 to $300+ per panel. Recommended for premium homes where roof space is limited or long-term performance matters.
Inverter brands commonly specified in Australian new builds: Fronius, SolarEdge, Enphase (microinverters), Growatt, Goodwe, Sungrow. Fronius and SolarEdge are widely regarded as premium options with strong local service support.
Note: Brand selection should be made in consultation with a CEC-accredited installer familiar with your local grid requirements and service network.
Feed-in Tariffs and Electricity Bill Savings
A solar system reduces your electricity bill in two ways: by powering your home directly during generation hours, and by exporting excess generation to the grid in exchange for a feed-in tariff credit.
In 2026, feed-in tariff rates typically range from 4 to 12 cents per kWh - substantially lower than the 25 to 45 cents per kWh most households pay to purchase electricity. This asymmetry means self-consumption is far more valuable than exporting.
For a standard 6.6kW system, typical annual electricity bill savings in 2026 range from $1,200 to $2,000. Most systems pay for themselves within 3 to 5 years.
To maximise self-consumption in a new home:
- Schedule high-load appliances including air conditioning, dishwasher and washing machine to run during peak solar hours - typically 10am to 3pm
- A smart home controller or solar diverter can automate this scheduling
- A hybrid inverter and battery allows evening consumption to be powered by stored solar
๐ก Typical annual savings: $1,200 to $2,000 for a 6.6kW system | Most systems pay for themselves in 3 to 5 years
EV Charging and Solar - Future-Proofing Your New Home
Electric vehicle ownership in Australia is growing rapidly. A new home build is the ideal opportunity to future-proof for EV charging at minimal cost.
During construction, running conduit for a dedicated EV charging circuit from the switchboard to the garage costs approximately $200 to $500 - versus $1,000 to $3,000 for a retrofit after the walls are closed. A 7kW AC wall charger costs $1,200 to $2,500 installed.
A solar system with a battery significantly improves EV charging economics - a 10kW system can generate enough surplus power during the day to meaningfully charge an EV. Confirm with your builder that conduit and three-phase power (if appropriate) are included in the build specification.
Solar Installation Process for a New Build
Design phase solar planning
Engage a CEC-accredited installer to review architectural plans, confirm roof orientation and size the system before design is finalised.
Conduit and pre-wiring during construction
The builder's electrician runs conduit from the roof space to the planned inverter location and confirms switchboard capacity before walls are closed.
Roof frame and truss confirmation
Confirm with the builder and structural engineer that trusses are designed to accommodate solar panel dead load and wind uplift.
Panel installation
Solar panels are mounted on the roof - ideally while construction scaffolding is still in place. For single-storey homes this can occur after roof completion.
Inverter and battery installation
The inverter is mounted at the planned location and wired to the switchboard. If a battery is included, it is installed and connected.
Electrical connection and testing
The solar installer connects the system to the switchboard, tests all components and confirms the system is generating correctly.
Grid connection and meter reconfiguration
The installer or electrician applies for grid connection with the local distributor and arranges smart meter installation or reconfiguration for solar feed-in.
System commissioning and handover
The installer commissions the system, provides documentation including warranties and user guides, and confirms monitoring is active.
How to Choose a Solar Installer for a New Build
BUILTLY and lasting project records
BUILTLY is building a record of completed Australian homes that credits the builder, architects, designers and trades behind each one.
Frequently asked questions
Should I install solar panels when building a new home in Australia?
Yes, for the vast majority of new home builds in Australia, installing solar during construction is the right decision. It is cheaper than retrofitting after handover, benefits from the federal STC rebate that steps down annually until 2030, improves your NatHERS Whole of Home rating and delivers immediate electricity cost savings from day one of occupancy. New South Wales BASIX requirements make solar effectively mandatory for new homes in that state.
How much do solar panels cost for a new home in Australia?
In 2026, a standard 6.6kW solar system - the most common residential size - costs $5,000 to $8,000 fully installed after the federal STC rebate. Budget approximately $1,000 per kilowatt installed as a planning figure. A 10kW system typically costs $8,000 to $10,500. Premium panels and inverters add 20 to 40 percent to these figures. Installing during construction rather than retrofitting typically saves $500 to $2,000 in scaffolding and conduit costs.
Does solar affect my NatHERS rating when building?
Solar panels do not affect the NatHERS thermal star rating, which is based on the building shell - orientation, insulation, glazing and materials. However, solar significantly affects the NatHERS Whole of Home rating required under NCC 2022, which all new homes must meet at a minimum of 60 out of 100. Solar generation offsets appliance energy use in the Whole of Home calculation and can be the deciding factor in achieving compliance for energy-intensive homes.
What size solar system do I need for a new home?
For a standard 3 to 4-bedroom Australian home, a 6.6kW system is the most common choice - generating approximately 24 to 28 kilowatt-hours per day on a north-facing roof. Larger homes, homes with electric vehicles or homes targeting battery storage should consider 10kW or larger. As a planning guide, budget approximately $1,000 per kilowatt installed and confirm sizing with a CEC-accredited installer who can model your specific roof orientation and household energy consumption.
Should I include a battery with my new home solar system?
For most new homes in 2026, the pragmatic recommendation is to install a hybrid inverter - battery-ready - and add a battery in the next two to five years as prices continue to decline. A hybrid inverter adds approximately $500 to $1,500 over a standard string inverter and means a battery can be added later without replacing the inverter. If you have time-of-use electricity tariffs, plan to charge an electric vehicle, or want backup power capability, installing a battery at handover may be worthwhile - particularly if the federal battery rebate of approximately 30 percent applies.
Related Guides
- NatHERS Rating Australia: What It Is, How It Works and How to Improve Your Score
- Air Conditioning for New Homes Australia: What to Know Before You Build
- Building a Passive House in Australia: Costs, Design and Complete Guide
- Sustainable Home Building in Australia: Builders, Costs and What to Expect
- Building Contract in Australia: What to Look For
- Provisional Sums in Building Contracts Australia
- Prime Cost Items in Building Contracts Australia
- Building a House Checklist in Australia
- How to Manage a Builder During Construction
- New Home vs Established Home in Australia
- Building a Luxury Home in Australia: Design, Costs and What to Expect
- How to Compare Quotes From Builders in Australia
- Insulation Australia: Types, Costs and What You Need to Know
- Smart Homes in Australia: What to Know Before You Build
Last updated: October 2026