Hot water is one of the largest single energy loads in an Australian home, commonly cited at roughly 15 to 30 percent of household energy use. In new builds, the system that carries that load has quietly shifted. Gas storage and instantaneous units, and conventional electric storage tanks, are steadily being replaced by heat pump hot water systems.
What a heat pump hot water system is
A heat pump hot water system heats water by moving heat rather than making it. A conventional electric storage system uses a resistance element, which converts electricity into heat at roughly a one to one ratio. A gas system burns fuel to produce heat directly. A heat pump instead extracts low grade heat from the ambient air outside and concentrates it into the water in a storage tank, using electricity only to drive a compressor and a fan.
The practical consequence is efficiency. Because the electricity is being used to move existing heat rather than create it, a heat pump typically delivers several units of heat energy for each unit of electricity consumed. That ratio is the whole argument. It is the reason the technology has moved from a specialist product into a mainstream new build inclusion, and the reason it is treated as a renewable technology under federal incentive arrangements.
This guide covers what the technology is, why it appears so often on new build specifications, the rebate position for a new home specifically, cost, placement and the questions to put to your builder or plumber. For the broader context on specifications and handover, refer to the BUILTLY complete guide to building a house in Australia.
How heat pump hot water works
The mechanism is the same refrigeration cycle used in a fridge or a split system air conditioner, run in the direction that produces useful hot water.
The cycle in plain terms
- A fan draws ambient air across an evaporator containing a refrigerant with a very low boiling point
- Even in cool air, the refrigerant absorbs enough heat to evaporate into a gas
- A compressor pressurises that gas, which sharply raises its temperature
- The hot gas passes through a heat exchanger wrapped around or immersed in the storage tank, transferring its heat into the water
- The refrigerant cools, condenses back to liquid, passes through an expansion valve and the cycle repeats
Integrated and split configurations
Integrated units place the compressor and fan directly on top of the tank as a single outdoor assembly. Split systems separate the compressor unit from the tank, which gives more freedom in siting the noisy component away from bedrooms and boundaries, at the cost of extra refrigerant lines and a slightly more involved installation.
Cold weather behaviour
Efficiency falls as ambient temperature drops, because there is less heat in the air to harvest. Most systems include an electric element as a backup for very cold conditions or unusually high demand. In colder climate zones, ask whether the proposed model is rated for the local design temperatures and how often the backup element is expected to engage, because heavy element use erodes the running cost advantage that justified the system.
Why it is being chosen for new builds
Three forces are pushing heat pumps onto new build specifications, and only one of them is running cost.
Running cost and efficiency
Against a conventional electric resistance tank, a heat pump uses a fraction of the electricity for the same volume of hot water. Against gas, the comparison depends on local tariffs, but the gap has narrowed sharply in the direction of electric as gas supply charges have risen. Actual savings vary by household size, tariff and climate zone, so treat any single advertised annual figure with caution.
The move away from gas connections
Several jurisdictions have moved to restrict or remove gas connections in new residential builds, and where that applies, hot water has to be electric. That turns the choice into resistance element versus heat pump rather than gas versus electric. The BUILTLY guide to the all electric new home in Australia covers how those restrictions differ by state and what an all electric specification changes across the rest of the build.
Energy rating and whole of home assessment
Current national energy provisions assess more than the building fabric. Appliance efficiency, including hot water, feeds into the whole of home component of the assessment, so a heat pump can help a design meet its target where the fabric alone is marginal. The BUILTLY guide to NCC 2022 7 star energy requirements sets out how the two halves of that assessment interact.
Pairing with rooftop generation
BUILTLY is building a record of completed Australian homes that credits the builder, designers and trades behind each one.
Rebates and incentives
This is the most misunderstood part of the topic for anyone building new, because most of the widely advertised hot water rebates in Australia are designed around replacing an existing system in an existing home, not fitting out a new one.
Federal small-scale technology certificates
Air source heat pump water heaters are eligible for small-scale technology certificates under the Small-scale Renewable Energy Scheme, administered by the Clean Energy Regulator. Eligible models are listed on the regulator's register of solar water heaters, which covers air source heat pumps with a capacity of no more than 425 litres, and the system must be installed exactly as listed for the certificates to be valid.
The number of certificates depends on the model, the postcode zone, the installation date and the deeming period. Certificate entitlements step down over time as the scheme approaches its legislated end in 2030, and the market price of a certificate moves, so the value of the discount is not a fixed number. In practice most households never handle certificates at all: the right to create them is assigned to a registered agent, usually the retailer or installer, in exchange for an upfront discount on the purchase price. This is the one incentive that clearly applies to a new installation in a new home.
State schemes and the new build limitation
The larger state incentives sit on top of the federal certificates for eligible households, but their eligibility rules are built around upgrades rather than new construction.
- Victorian Energy Upgrades - offers discounts on approved heat pump and solar hot water products, but the building where the upgrade takes place must be at least two years old and an existing gas or electric system is being replaced
- Solar Homes hot water rebate (Victoria) - rebates of up to $1,000 for eligible heat pump and solar hot water products, rising to up to $1,400 for eligible locally made products, with a household income test that tightens to $150,000 or less per year from 1 July 2026
- NSW Energy Savings Scheme hot water upgrade incentive - a discount available to households and small businesses installing or replacing a hot water system with an efficient heat pump or solar unit, delivered through accredited providers
Scheme rules, amounts and eligibility change regularly, and the age of dwelling and replacement conditions frequently exclude brand new homes from state discounts. Confirm current eligibility with your installer and the administering body before treating any rebate as part of your build budget.
The practical instruction for a new build is simple. Ask the builder or plumber to show the certificate discount as a separate line on the quote, and ask in writing whether any state rebate has been assumed. A quote that quietly builds in a state rebate the dwelling cannot claim is a quote that will move.
Cost considerations
A heat pump system carries a higher upfront cost than a conventional electric storage tank or a standard gas unit. Supplied and installed pricing for residential systems generally sits in the low to mid thousands of dollars before any certificate discount, with split configurations and larger tanks at the upper end. On a new build the differential over the base inclusion, rather than the total, is the number that matters, because the builder's base specification usually already includes some hot water system.
Several build stage factors move the installed cost:
- Distance between the unit location and the switchboard, and whether a dedicated circuit is required
- Split configuration, which adds refrigerant line runs and a second mounting location
- Slab, plinth or bracket requirements at the unit position
- Tempering valve, relief drainage and condensate drainage arrangements
- Acoustic treatment or relocation where a boundary condition is tight
On payback, be careful with confident numbers. The honest framing is that the recovery period depends on the system being replaced in the comparison, the household's hot water volume, the electricity tariff, whether the run schedule can be shifted onto self-consumed solar, and the certificate discount received at purchase. Households replacing an expensive resistance element load see the shortest recovery. Households comparing against cheap off peak arrangements see a longer one.
Maintenance is also part of the cost picture. Heat pumps have moving parts that a resistance element does not, so budget for periodic servicing and eventual compressor life, and read the warranty terms on the tank and the compressor separately, because they are commonly different periods.
Installation and placement considerations
Placement is the decision most likely to be regretted, and it is made early, often on a plan and without much thought.
Noise and neighbours
A heat pump has a compressor and a fan, so it makes a continuous low hum while running, similar in character to an air conditioner outdoor unit. On modern small lots, where the side setback can be a couple of metres and a neighbour's bedroom window sits directly opposite, that noise becomes a genuine dispute risk. Manufacturers publish sound ratings for each model, and local noise provisions restrict what is acceptable at a boundary, particularly at night. Three practical mitigations apply: place the unit away from bedroom windows on both properties, avoid narrow side passages where sound reflects between two walls, and set the operating schedule to daytime hours rather than overnight.
Airflow, clearance and support
The unit needs a free flow of ambient air, so manufacturer clearances around the intake and discharge must be respected and cannot be compromised later by a fence, a rainwater tank, a screen or landscaping. Position the unit where discharged cool air does not blow into an outdoor living area. A full tank is heavy, so it needs an appropriate slab, plinth or bracketed support designed for the loaded weight rather than the empty one.
Plumbing, drainage and electrical
Installation is licensed plumbing work with an electrical component, and it involves tempering valve requirements, relief and condensate drainage to an approved point, and a supply circuit at the switchboard. The BUILTLY guide to what a plumber does in construction covers where hot water rough-in and fit-off sit in the build sequence and what compliance paperwork the trade issues at completion.
What to check before installing
- The exact model proposed, and confirmation that it appears on the Clean Energy Regulator's register if certificates are being claimed
- The certificate discount shown as a separate line on the quote, and whether any state rebate has been assumed on a dwelling that may not qualify
- Tank size and the household occupancy the installer has assumed in sizing it
- Performance in the local climate zone, and how often the backup element is expected to run in winter
- The published noise rating and the proposed unit location relative to bedroom windows on both properties
- Manufacturer clearances at the chosen position, checked against fences, tanks and future landscaping
- Warranty terms on the tank and the compressor separately, plus what servicing is required to keep them valid
- That the installer holds current plumbing and, where relevant, refrigerant handling and electrical credentials
- Whether scheduling or timer control is included, so the system can run on daytime solar generation later
Credentials are worth verifying rather than assuming, both for the trade and for the builder coordinating them. The BUILTLY guide on how to check a builder's licence in Australia lists the state registers to search.
BUILTLY and lasting project records
Hot water is one of those inclusions that disappears from memory the moment the house is handed over. The model, its capacity, its installation date, the compliance paperwork and the warranty terms all matter again years later, at the first service call or the first sale.
BUILTLY is building a record of completed Australian homes that credits the builder, designers and trades behind each one.
Frequently asked questions
Can I get a rebate on a heat pump hot water system in a brand new home?
Usually only the federal incentive. Air source heat pump water heaters listed on the Clean Energy Regulator's register of solar water heaters can earn small-scale technology certificates under the Small-scale Renewable Energy Scheme, and that applies to a new installation in a new home. The larger state schemes work differently. The Victorian Energy Upgrades program requires the building to be at least two years old and an existing gas or electric system to be replaced, and the NSW Energy Savings Scheme hot water incentive is likewise framed around installing or replacing a system in an existing premises. Confirm eligibility with your installer before assuming a state discount applies to a new build.
How many small-scale technology certificates does a heat pump earn?
It depends on the specific model, your postcode zone, the installation date and the deeming period selected. The Clean Energy Regulator publishes a register of eligible air source heat pumps with a capacity of no more than 425 litres, and a solar water heater certificate calculator for working out entitlements. Certificate entitlements decline as the scheme approaches its legislated end in 2030, and the dollar value of a certificate moves with the market, so the sensible approach is to ask for the discount to be shown as a line item on the quote rather than relying on an advertised figure.
Are heat pump hot water systems noisy?
They contain a compressor and a fan, so they produce a low mechanical hum while running, broadly comparable to the outdoor unit of a split system air conditioner. On a standard suburban block this is manageable but not something to leave to chance. Manufacturers publish a sound power or sound pressure rating for each model, and local noise provisions restrict what is acceptable at a neighbouring boundary, particularly at night. Placement away from bedroom windows and neighbouring outdoor living areas, plus a run schedule set to daytime hours, resolves most complaints before they happen.
Does a heat pump work with solar panels?
Yes, and pairing the two is one of the main reasons heat pumps are specified in new builds. Because the tank stores heat, the system can be scheduled to run in the middle of the day when a rooftop array is generating, which shifts the load onto self-consumed generation rather than grid supply. This only works if the system has a timer or scheduling control and the installation allows for it, so raise the intention at specification stage rather than after handover.
What size heat pump does a household need?
Sizing follows household occupancy and peak demand rather than floor area. Common residential tank sizes sit around 200 to 300 litres, with larger households and homes with high simultaneous demand moving up from there. Undersizing produces run-out complaints in winter, when ambient air is colder and recovery is slower. Oversizing wastes capital and standing losses. Ask the installer to state the assumed occupancy behind the size they have proposed so the assumption can be checked against how the household actually lives.