A home battery is now one of the larger discretionary purchases an Australian household makes, and the specification sheets are written for installers rather than owners. Two products with the same headline kWh figure can behave very differently in a real home, and the difference usually sits in numbers most buyers never look at.
What this guide covers
This guide is about the battery system itself: how storage capacity is measured and sized, what continuous power output means in practice, the chemistry and warranty terms on offer in the Australian market, how the battery couples to your inverter, what a complete installation costs, and how to read a quote properly before you sign it.
It deliberately stops short of two neighbouring subjects. If you are building and want the house wired so a battery can be added cleanly later, that is build-stage provisioning and it is covered in solar and battery ready home design in Australia, which deals with conduit routes, switchboard space, structural roof capacity and where the unit will physically sit. Nothing in this guide repeats that work. If you are still deciding on the solar array itself, its size, orientation and general economics, start with solar panels for new homes in Australia, which gives the system-level overview. This guide picks up where that overview leaves off and goes into the storage hardware in detail.
For the surrounding build context, including specifications, variations and handover records, refer to the BUILTLY complete guide to building a house in Australia.
Battery capacity and sizing
Capacity is measured in kilowatt-hours, written kWh. One kWh runs a 1,000 watt appliance for one hour. A typical Australian household consumes somewhere between 12 and 25 kWh a day across the whole day, but only a portion of that falls after sunset, and it is the after-sunset portion a battery is actually covering.
Usable capacity versus nominal capacity
This is the single most misunderstood figure in residential storage. Nominal, or rated, capacity describes the total energy held in the cells. Usable capacity is what the battery management system will actually release to your home. Manufacturers hold a reserve back to limit depth of discharge, protect cycle life, and on some products keep a floor of charge available for blackout backup.
The gap between the two numbers varies by product. Some lithium iron phosphate units publish a usable figure very close to nominal because the chemistry tolerates deep cycling. Others reserve ten percent or more. When you compare a 10 kWh unit against a 13.5 kWh unit, you may in practice be comparing 9.6 kWh against 12.2 kWh, and the price per usable kWh shifts accordingly.
Ask for usable capacity in writing, and check whether the figure quoted is at the beginning of life or at end of warranty. Those are two different numbers on the same product.
Sizing against your own consumption pattern
Correct sizing comes from your actual load profile, not from a rule of thumb. Two households with identical annual consumption can need very different batteries depending on when they use power.
- Evening-heavy households - most consumption after 5pm, so a larger battery is well used every day and cycles fully
- Daytime-heavy households - people home during the day, solar is consumed directly, and a smaller battery covers a modest evening tail
- Electric vehicle owners - charging behaviour dominates the profile and a battery sized for the house alone will be drained by one charging session
- All-electric homes - induction cooking, reverse cycle heating and electric hot water shift both the volume and the timing of load
The practical method is to pull twelve months of interval data from your retailer, which most now provide on request, and look at overnight consumption between sunset and sunrise across a winter week and a summer week. That overnight figure, not your daily total, is the number a battery has to cover. Oversizing beyond it means paying for capacity that never cycles, which erodes the return without improving the outcome.
Matching storage to array output
A battery can only store surplus that the array actually produces. If a 6.6 kW system exports only a few kWh on an average winter day, a very large battery will spend most of the cooler months partially charged. Storage and generation should be sized together, with the weakest generating season sanity-checked rather than the best one.
Be cautious with sizing based on a single summer bill. Winter generation in the southern states can fall to a third of summer output, and a battery sized on peak-season surplus will sit underused for months of the year.
Continuous power output
Capacity and power output are separate specifications and both belong in your comparison. Capacity in kWh tells you how long the battery can run the house. Continuous power output in kW tells you what the battery can run at any single moment. A large tank with a narrow tap is still a narrow tap.
Most residential batteries sit somewhere around 3 kW to 7 kW of continuous output, with a short-duration peak rating above that for motor start-up surges. To make sense of the figure, add up what might run at once on a winter evening.
- Ducted reverse cycle air conditioning can draw 3 kW to 6 kW on its own
- An electric oven draws roughly 2 kW to 3 kW while heating
- An induction cooktop can exceed 3 kW with two zones on high
- A kettle is around 2.4 kW, briefly, but it lands on top of everything else
- Baseline lighting, fridge, electronics and standby loads sit around 0.3 kW to 0.8 kW
On grid-connected operation, exceeding the battery output is unremarkable. The system simply tops up the shortfall from the grid and you pay for the difference. The practical consequence is that a battery with modest output saves less than you expected on exactly the evenings when tariffs are highest.
Where output matters most: backup
In a blackout the grid is not there to make up the shortfall, so output becomes a hard ceiling. If the backup circuit is carrying a 5 kW load demand against a 3.3 kW battery, the system trips out. This is why backup installations usually cover nominated essential circuits, typically lighting, power points, the fridge and internet, rather than the whole switchboard.
Questions worth asking about backup
Ask which circuits are on the backup board, what the changeover time is, whether solar continues to generate and recharge the battery during an extended outage, and whether motor loads such as a pool pump or air conditioner compressor are excluded. A system that cannot recharge from solar during an outage is only good for one night.
Battery chemistry and warranty
Almost all residential storage sold in Australia is lithium-ion, but the sub-chemistries behave differently and the warranty is where that difference is priced.
Lithium iron phosphate (LFP)
LFP is the dominant chemistry in the Australian residential market. It is thermally stable, tolerates daily deep cycling well, and typically supports higher cycle counts than the alternatives. The trade-off is lower energy density, so an LFP unit is usually physically larger and heavier for the same stored energy, which matters if it is being wall mounted on a lightweight frame.
Nickel manganese cobalt (NMC)
NMC packs more energy into a smaller and lighter enclosure, which suits constrained installation locations. It is generally more sensitive to heat, which makes the installation position and ventilation more important in warmer climates. Both chemistries are installed under the same Australian standards for battery installation, and both require the installer to observe clearances, separation from habitable spaces and location rules.
Reading the warranty properly
A battery warranty is not a single number. It is usually three conditions applied together, and the battery is only covered while all three hold.
- Term in years - commonly ten years on mainstream residential products
- Cycle count or throughput - a maximum number of full cycles, or a total energy throughput in MWh, whichever is reached first
- Capacity retention - a guaranteed remaining usable capacity at the end of the term, often around 60 to 70 percent, occasionally higher
The interaction between these is where owners get caught. A ten year term paired with a throughput cap that a heavy user reaches in seven years is a seven year warranty for that household. A generous cycle allowance paired with a low retention guarantee means the battery can legitimately degrade a long way and still be within warranty.
Who actually honours it
Check whether the warranty is supported by an Australian entity with local presence, and what the process is if the manufacturer exits the market. Confirm whether labour and removal are covered or only the replacement unit, because a swap-out on a wall-mounted battery is a real cost. Confirm too that Australian Consumer Law rights sit alongside the manufacturer warranty and are not displaced by it.
Inverter compatibility: AC vs DC coupling
Solar panels generate direct current. Your home runs on alternating current. Where the battery sits relative to that conversion is what AC and DC coupling describe, and it has real consequences for cost and efficiency.
DC coupling
The battery connects on the DC side, sharing a single hybrid inverter with the solar array. Solar energy goes into the battery without being converted to AC first, so there is one conversion step instead of two and round-trip efficiency is slightly better. It is the tidier arrangement when solar and storage are installed together, and it means one inverter, one warranty and one monitoring platform.
The limitation is flexibility. The battery must be compatible with the hybrid inverter, the choice of battery is narrowed to what that inverter supports, and total system capacity is bounded by the inverter rating.
AC coupling
The battery has its own inverter built in and connects on the AC side of the switchboard, alongside the existing solar inverter. Energy is converted from DC to AC by the solar inverter, then back to DC to charge the battery, then to AC again on discharge. That extra step costs a few percent in round-trip efficiency.
What you get in return is independence. The existing solar inverter stays in place, the battery choice is not constrained by it, and the two systems can be replaced on separate timelines.
Which suits which situation
For a new installation where solar and storage are being purchased together, DC coupling through a hybrid inverter is usually the better value and the neater result. For a retrofit onto a working solar system that still has years of warranty left, AC coupling is normally the sensible path, because replacing a functioning inverter to gain a small efficiency margin rarely pays for itself.
One caution on retrofits: adding storage can change the way your installation is classified and may require the existing system to be brought to current standards. Any work on the switchboard forms part of the certified electrical work for the property, so ask how the change is documented. The BUILTLY guide to electrical compliance certificates in Australia sets out what you should receive and keep.
Cost and installed pricing
Installed pricing is more useful than hardware pricing, because the labour, switchboard work, mounting and commissioning are a meaningful share of the total. As a planning range in 2026, residential storage commonly lands between roughly $800 and $1,400 per usable kWh installed before any rebate, with larger systems generally cheaper per kWh than small ones because the fixed installation cost is spread further.
Several things move a quote within and beyond that band.
- Backup capability - a backup board, changeover device and additional wiring is a distinct cost, not an included feature
- Switchboard condition - an older or full board may need upgrading before the battery can be connected
- Installation location - garage wall against structural backing is straightforward, and an outdoor location with weather protection or a long cable run is not
- Single or three phase - three phase properties and three phase backup add complexity
- Inverter change - a DC coupled retrofit that requires a hybrid inverter carries that inverter cost too
On rebates, the federal Cheaper Home Batteries Program has since 1 July 2025 discounted eligible installed battery systems by roughly 30 percent of the installed cost, delivered through small-scale technology certificates and applied by the installer as an up-front reduction rather than paid to you afterwards. The subsidy value per usable kWh steps down each year of the program, so the discount available at the time you sign is the one that matters. Eligibility conditions apply to the product, its usable capacity and the accreditation of the installer, and some states run additional or complementary schemes. Confirm the current figure and your eligibility with your installer and against the program rules before treating any rebate as certain.
Being honest about payback
Payback depends on your tariff structure, your overnight consumption, your feed-in rate and how fully the battery cycles each day. Those variables differ so much between households that any single advertised payback figure should be treated as marketing rather than analysis. What is reasonable to say is that batteries perform best financially where feed-in tariffs are low, evening consumption is high, and time-of-use pricing creates a wide gap between peak and off-peak rates.
It is also fair to note that many households buy storage for reasons other than return: reducing exposure to price movements, keeping essential circuits alive during outages, or using more of what their own roof produces. Those are legitimate motivations, and they are easier to defend than a spreadsheet built on assumed future tariffs.
How to evaluate a quote
A complete storage quote is a technical document. If it fits on half a page with a brand name and a total, it is not a quote, it is a price.
What a genuine quote includes
- Battery make, model, nominal capacity and usable capacity stated separately
- Continuous power output in kW and the peak or surge rating
- Inverter make and model, and whether the system is AC or DC coupled
- Warranty term, cycle or throughput limit, and the end-of-term capacity retention figure
- Whether backup is included, which circuits it covers, and the equipment used to achieve it
- Any switchboard upgrade, and whether it is included or excluded
- Installation location, mounting method and any make-good
- The rebate amount applied, how it is claimed, and the price before and after it
- Installer licence and accreditation details, and who is performing the electrical work
- Commissioning, monitoring setup, handover documentation and the electrical certificate
Red flags
- Only nominal capacity quoted, with usable capacity absent or described as equivalent
- No kW output figure anywhere in the document
- Backup implied in conversation but not itemised in writing
- A price well under the market band with no explanation of what has been left out
- Pressure tactics tied to a rebate that is described as expiring within days
- Savings or payback presented as a guaranteed figure
- No named licensed electrician, or subcontracting arrangements left vague
- Warranty described only in years, with cycle and retention terms not disclosed
Verify the licence and accreditation of whoever will do the work before you accept anything, using the approach in how to check a builder's licence in Australia. If the storage installation forms part of a larger build or renovation contract, check how it interacts with your existing cover, as set out in construction insurance in Australia. And if you are specifying several electrical systems at once, the same evaluation discipline applies to heat pump hot water in new homes, where usable output and rebate eligibility are the equivalent traps.
BUILTLY and lasting project records
Storage is a five-figure purchase installed by a trade whose work is largely invisible once the cover is on. Price is the easiest thing to compare and the least informative. A genuine track record of correctly installed and properly documented systems tells you far more about what you will receive.
BUILTLY is building a record of completed Australian homes that credits the builder, designers and trades behind each one.
Frequently asked questions
What is the difference between nominal and usable battery capacity?
Nominal capacity is the total energy the cells hold on paper. Usable capacity is the portion the battery management system will actually let you draw, because a reserve is held back to protect cell life and, on some products, to keep a minimum charge available for backup. A battery advertised at 13.5 kWh may deliver closer to 12.2 to 13.5 kWh depending on the product and its depth of discharge limit. Compare products on usable kWh, not headline kWh, and confirm the figure is stated in the quote rather than in a brochure.
Why does a battery have both a kWh rating and a kW rating?
kWh describes how much energy is stored, which determines how long the battery can run your home. kW describes how fast that energy can be delivered, which determines what the battery can run at any one moment. A large battery with a modest continuous output rating will happily cover overnight lighting, fridge and standby loads but may not carry an oven, an induction cooktop and a ducted air conditioner simultaneously. Both numbers need to be checked against your actual loads.
What battery chemistry is most common in Australian homes?
Lithium iron phosphate, usually written as LFP or LiFePO4, is the dominant chemistry in residential storage sold in Australia. It is favoured for thermal stability, long cycle life and tolerance of daily deep cycling. Nickel manganese cobalt, written as NMC, is also present and offers higher energy density in a smaller enclosure. Both are lithium-ion families and both are installed under the same Australian installation standards, so the practical decision usually comes down to warranty terms, footprint and installer support.
Do I need a hybrid inverter to add a battery?
No. A DC coupled battery needs a hybrid inverter, which is the neatest option when solar and storage are installed at the same time. An AC coupled battery has its own inverter built in and connects on the AC side of the switchboard, which is how most retrofits to an existing solar system are done. AC coupling avoids replacing a working solar inverter and is often the practical choice for an established system, at the cost of one extra conversion step.
Does a home battery keep the power on during a blackout?
Only if backup is specifically included and wired. A standard grid connected battery shuts down during an outage for safety unless it is installed with a backup circuit and a changeover device that isolates the home from the grid. Backup capability is a separate line item, it usually covers nominated essential circuits rather than the whole house, and it needs to be written into the quote. If continuous power matters to you, ask which circuits are covered and what the transfer behaviour is.